A Remix of punk juggle's Cabfare 22lr Pistol by nameisnight

Release Date: 02/23/2022
Latest Update: 03/05/2022

While I like the original version of the Cabfare I found some issues and things I wanted to change, so I remixed it, now calling it the Gambino 22lr.

============================== !! READ ME !! ==============================
Only use proper 22lr Barrel Liners with Rifling, Otherwise its Illegal and Dangerous
Only use Strong Epoxy such as JB Weld or Lock tight for the Barrel and Dime Breech
For first shots use a empty 22lr shell will bullet and gunpowder removed, Check for Issues.
For second shot use a Sub-Sonic 22lr bullet and fire remotely or at least use thick gloves and safety glasses, Check for issues.

If all pass and the gun does not show any cracks, brakes or issues, Shoot with caution and always check the gun for issues.

===========================================================================

Along with all the required parts from the original package (1.2) you will need the following

1 US Dime (.10c)
1 Drilling Tool
1 3.5 mm Drill Bit
1 6 mm Drill Bit

Use PLA+ or Stonger, 100% Infill, 20 Walls, No Brim, No Raft, No Supports. .20 = OK .16 = GOOD .12 = BEST

You will need to print
x1 Left Frame
x1 Right Frame
x1 Left Grip
x1 Right Grip
x2 Striker Grips
x1 Sear
x1 Trigger
x1 Striker
x1 Take down
x1 Dime Jig

All other files are Optional

=======================================================================

Build Instructions

Threaded Barrel:
Print at 100% infill, Max walls and Vary high resilution for the threads. Recommend .12 or lower.

Supressed Barrel:
Print Settings:
PLA+ or Stronger
.16 or Lower Detail
100% Infill
20 Walls Top and Bottom
Print front down on bed
NO Supports

Build:
	Use a 65mm 22lr Rifled Barrel Liner with a OD of 8mm
	Use a 8mm drill bit to pre-drill the hole in the barrel from the breech side down, keep stright!
	Use pliers or sandpaper to scratch the outside of the barrel for more surface area
	Use 2 part strong Epoxy (JB Weld, Locktight, etc) and wipe the barrels outside with a generus layer
	Press the barrel into the barrel body from the breech side, make sure end of liner is level with the barrel frame!
	Clean leftover Epoxy, If some epoxy gets in the barrel liner clean out.

NOTICE:
	Please now your laws before printing, This is a NFA item in the United States!
	Be sure that your barrel liner is inline with the ports of the baffles or you will have baffle strikes!
	Always do test shots remotely with a vice and string!
	Use Sub-Sonic ammo like Aquila SSS for best results.

Using the Dime Jig:
Seat dime into the slot on the bottom of the jig so its flush with the jigs body. It should snap into place.
Clamp jig into vice or C-Clamp to hold in place
Drill hole through drill port in the jig, go-slow and using water if needed for cooling.
Remove Dime from jig and use Vice or C-Clamp to hold dime
Use 6 mm Drill bit to chamfer holes on both sides

Post Processing (After Printing):
Use file or light sandpaper to smooth and remove any imperfections, zits, bumps, etc from the frame and make sure all areas are level.
Use water if needed to help sand.

Dime Breech:
After assembling gun make sure that the striker pin is properly aligned with the striker port on the dime, re-drill if needed.
Epoxy into place once aligned properly.

Striker Grips:
If printed correct they should friction or snap fit onto the striker, if not simple epoxy on.

=======================================================================

Trouble Shooting:

If barrel flings open when shot: Your Take down level isn't all the way into the barrels notch, you may need to sand it to make it fit or you may need a stringer spring
Bad Primer Strikes: Your striker pin may not be correct you want to shave/sand to opposite sides of the screw to a near point, but leave a flat area about 1 mm. You may also need a stronger spring, or you could be catching on the Dime Breech.
Hard to Cock/Fire: Sand smooth all moving parts and apply Plastic Safe lubrication

=======================================================================

Change log:

03/05/2022 - 1.7
	Added Solid Short Barrel
	Added Solid Standard Barrel
	Added Solid Threaded Short Barrel
	Added Basic Trigger
	Added Flat Trigger

03/05/2022 - 1.6
	Added Railed version with Sight notch

03/04/2022 - 1.5
	Added Integrally Suppressed Barrel (Beta)
	Added Railed Frame and Grips
	Added Grip Plug
	Added 1/2-28 Threaded Barrel

02/23/2022 - Orignial Release
	Added Frame Alignment "Peg" and "Hole"
	Stiffened Breech
	Added "DIME" breech
	Removed Top charging handle/rear sights
	Added dual side charging handles
	Added Vz.61 Style Charging Handle Grips
	Reworked Se)