Parlor Pistol

about

# Parlor Pistol

#### Author
Caboose

#### Version
1.0

#### Description

The goal of this project was to make a small parlor pistol. As always, I aim to avoid rafting and support. This parlor pistol is inspired by http://www.thingiverse.com/thing:212279 which is a toy dart pistol of my design.

You can see a demonstration here: http://youtu.be/l3LeLbWkE0o of the toy pistol.

Trigger is not a classic trigger where the user pulls back, instead, you push your finger forward to fire the gun.

To load the gun, pull back the bolt, hold, and then push the trigger upwards towards the receiver. Next load projectile, and fire as stated above.

Material used: ABS (but PLA may work, just not for barrel!)

Print all parts at 100% infil, 1 or 2 shells, depending on preference. 2 recommended. No rafting or support needed. All parts are correctly oriented for printing.

#### Assemble

To assemble, screw the screw into the bolt. Insert bolt into receiver, push to front. Insert spring. Insert 50mm screw from top, and push through. Next attach the grip to the receiver. Push 50mm screw all the way through the grip, and cap with M3 nut. Next add the trigger to the front of the gun, and hold, add muzzle. Finally put a 25mm screw through the front hole, cap with nut.

####Load and Fire

This gun is not safe. I'm not responsible for you getting hurt. There is no safety. I am not going to add a safety. No safety is implied.

Pull back bolt, push up trigger. Remove barrel. Insert .177 pellet in barrel. Add 409 shotgun primer on top, pushing .177 pellet into barrel. Push barrel into muzzle (now I regret naming this muzzle...). Twist 90 degrees. Aim, fire.

#### Parts List

* Body
* Grip
* Trigger
* Bolt
* Barrel
* Muzzle
* RearPlate

#### Hardware (all available from McMaster-Carr):

* 2 x M3 Nuts (http://www.mcmaster.com/#90685A037)
* 1 x M3 50mm Screw (http://www.mcmaster.com/#91290A137)
* 1 x M3 25mm Screw (http://www.mcmaster.com/#91290A123)
* 1 x #9657K331 Steel Compression Spring (http://www.mcmaster.com/#9657K331)
* 1 x Screw as firing pin, multiple types will work, dull end slightly with file

files

File Extension
Parlor_Pistol-Caboose.rar rar

versions

Version: 1.0.0 latest

Initial Release

about

# Parlor Pistol

#### Author
Caboose

#### Version
1.0

#### Description

The goal of this project was to make a small parlor pistol. As always, I aim to avoid rafting and support. This parlor pistol is inspired by http://www.thingiverse.com/thing:212279 which is a toy dart pistol of my design.

You can see a demonstration here: http://youtu.be/l3LeLbWkE0o of the toy pistol.

Trigger is not a classic trigger where the user pulls back, instead, you push your finger forward to fire the gun.

To load the gun, pull back the bolt, hold, and then push the trigger upwards towards the receiver. Next load projectile, and fire as stated above.

Material used: ABS (but PLA may work, just not for barrel!)

Print all parts at 100% infil, 1 or 2 shells, depending on preference. 2 recommended. No rafting or support needed. All parts are correctly oriented for printing.

#### Assemble

To assemble, screw the screw into the bolt. Insert bolt into receiver, push to front. Insert spring. Insert 50mm screw from top, and push through. Next attach the grip to the receiver. Push 50mm screw all the way through the grip, and cap with M3 nut. Next add the trigger to the front of the gun, and hold, add muzzle. Finally put a 25mm screw through the front hole, cap with nut.

####Load and Fire

This gun is not safe. I'm not responsible for you getting hurt. There is no safety. I am not going to add a safety. No safety is implied.

Pull back bolt, push up trigger. Remove barrel. Insert .177 pellet in barrel. Add 409 shotgun primer on top, pushing .177 pellet into barrel. Push barrel into muzzle (now I regret naming this muzzle...). Twist 90 degrees. Aim, fire.

#### Parts List

* Body
* Grip
* Trigger
* Bolt
* Barrel
* Muzzle
* RearPlate

#### Hardware (all available from McMaster-Carr):

* 2 x M3 Nuts (http://www.mcmaster.com/#90685A037)
* 1 x M3 50mm Screw (http://www.mcmaster.com/#91290A137)
* 1 x M3 25mm Screw (http://www.mcmaster.com/#91290A123)
* 1 x #9657K331 Steel Compression Spring (http://www.mcmaster.com/#9657K331)
* 1 x Screw as firing pin, multiple types will work, dull end slightly with file

Download

creator

organization

Metrics

Views

4K

Downloads

361

Project Info

release date

Feb 20, 2020

artifact type

Printable project

library category

Printable Firearms

fabrication method

Primarily Printable

fabrication tool

3D Printer

release country

United States

language

English

license

No license

Firearm Info

type

Pistol

caliber

.177

version hash

QmRCZ2PAeNWb9RNFYwHo5NmMNStgAhmqZ5EJkbGQjMZSNT

files

File Extension
Parlor_Pistol-Caboose.rar rar

versions

Version: 1.0.0 latest

Initial Release

The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.

Ghost Gunner 3s, GG3s, True Desktop CNC, by Defense Distributed Ghost Gunner 3s, GG3s, True Desktop CNC, by Defense Distributed

Javascript & cookies are required to view this site.