Revo1ution AKM Magazine V1.0.1

about

Revo1ution AKM Magazine V1.0.1: FFFTech/FFFTechnology

A 3DP magazine for AK pattern firearms chambered in 7.62x39.

Features a reinforced ribbed magazine body, a thickened baseplate to absorb impacts from drops, an anti-friction follower, and a separately printed rear locking lug (Read Notes)

This design also allows the use of AR-15 magazine springs via alternate follower and floorplate versions, for Western (North American countries) builders; as AR-15 magazine springs are often cheaper and easier to acquire. 

Tested with:

 * Palmetto State Armory PSAK-47 GF3
 * Zastava M70, Imported Civilian Semiauto Model


Two follower and floorplate versions are available: 

 *Standard: AK Spring usage
 *AR: AR-15 Spring usage, labeled on each part. 

Two magazine bodies are available: 

 *28rd: As long as a factory manufactured 30rd mag.
 *30rd: 7mm longer than the 28rd mag body. 


Update V1.0.1: Reduced advised extruder/nozzle printing temperature from 230C to 220C.

 

Printer Used: Ender 3 V2

Filament Used: PLA+

Print Settings:

Extruder: 220C (Yes, you need to print the parts HOT)
Bed: 56C 
First Layer Print Height: .2mm 
Standard Layer Height: .16mm
Wall Perimeters: 7+ 
Infill: 32%+
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%

Print ALL the parts on their bases, and use tree supports.

 

Hardware Needed:

1x Standard Length AK Mag Spring
1x Standard Length AR-15 Mag Spring (OPTIONAL)

 

Parts Installation:

1) Apply cyanoacrylate adhesive inside the pocket for the rear locking lug. If the rear locking lug is slightly loose in the pocket, apply Clear Gorilla Glue. Wait 24hrs for the adhesive to cure. 

2) Insert the rear locking lug, with the angled facet facing outwards, and down towards the mag body's base. 

3) Lightly sand the anti-friction follower's sides and curved spine.

4) Slide the top of the magazine spring through the front of the follower, above the spring retention tab.

5) Attach the floorplate to the bottom of the magazine spring, making sure the first spring winding snaps over the retainers. 

6) Slide the internal spring assembly into the magazine body.

7) Depress the floorplate, and slide on the baseplate. The floorplate's locking tab must index with the channel in the baseplate. 

 

Notes: 

1) Previous 3D printed AK magazines with an integrated locking lug often had said lug shear off. With the orientation the mags are meant to be printed, by the layer height to which the lug is located, the layers are perpendicular to its thinnest cross section.  A separate printed lug allows for printing the layers parallel with it's thickest cross-section, making the lug 
much more durable. 

2) Polish, Bulgarian, Serbian, and US based Magpul springs have been tested. The only spring that did NOT work (that was tested) was made by a US based company under the name Falcon Arms. (We could only load 24/28rds)

 

Accreditations:

Yeezy: Inspired the concept for AR-15 mag spring compatibility for Western builders.

Freeman1337: Advised AR-15 mag spring compatible parts; printed and tested mag with AR-15 spring adapted follower and floorplate. Provided images and testing video footage. Gave data on fitment for AR-15 spring compatible parts. 

files

File Extension
Revo1ution AKM Magazine V1.0.1.zip zip

versions

Version: 1.0.0 latest

Initial release

about

Revo1ution AKM Magazine V1.0.1: FFFTech/FFFTechnology

A 3DP magazine for AK pattern firearms chambered in 7.62x39.

Features a reinforced ribbed magazine body, a thickened baseplate to absorb impacts from drops, an anti-friction follower, and a separately printed rear locking lug (Read Notes)

This design also allows the use of AR-15 magazine springs via alternate follower and floorplate versions, for Western (North American countries) builders; as AR-15 magazine springs are often cheaper and easier to acquire. 

Tested with:

 * Palmetto State Armory PSAK-47 GF3
 * Zastava M70, Imported Civilian Semiauto Model


Two follower and floorplate versions are available: 

 *Standard: AK Spring usage
 *AR: AR-15 Spring usage, labeled on each part. 

Two magazine bodies are available: 

 *28rd: As long as a factory manufactured 30rd mag.
 *30rd: 7mm longer than the 28rd mag body. 


Update V1.0.1: Reduced advised extruder/nozzle printing temperature from 230C to 220C.

 

Printer Used: Ender 3 V2

Filament Used: PLA+

Print Settings:

Extruder: 220C (Yes, you need to print the parts HOT)
Bed: 56C 
First Layer Print Height: .2mm 
Standard Layer Height: .16mm
Wall Perimeters: 7+ 
Infill: 32%+
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%

Print ALL the parts on their bases, and use tree supports.

 

Hardware Needed:

1x Standard Length AK Mag Spring
1x Standard Length AR-15 Mag Spring (OPTIONAL)

 

Parts Installation:

1) Apply cyanoacrylate adhesive inside the pocket for the rear locking lug. If the rear locking lug is slightly loose in the pocket, apply Clear Gorilla Glue. Wait 24hrs for the adhesive to cure. 

2) Insert the rear locking lug, with the angled facet facing outwards, and down towards the mag body's base. 

3) Lightly sand the anti-friction follower's sides and curved spine.

4) Slide the top of the magazine spring through the front of the follower, above the spring retention tab.

5) Attach the floorplate to the bottom of the magazine spring, making sure the first spring winding snaps over the retainers. 

6) Slide the internal spring assembly into the magazine body.

7) Depress the floorplate, and slide on the baseplate. The floorplate's locking tab must index with the channel in the baseplate. 

 

Notes: 

1) Previous 3D printed AK magazines with an integrated locking lug often had said lug shear off. With the orientation the mags are meant to be printed, by the layer height to which the lug is located, the layers are perpendicular to its thinnest cross section.  A separate printed lug allows for printing the layers parallel with it's thickest cross-section, making the lug 
much more durable. 

2) Polish, Bulgarian, Serbian, and US based Magpul springs have been tested. The only spring that did NOT work (that was tested) was made by a US based company under the name Falcon Arms. (We could only load 24/28rds)

 

Accreditations:

Yeezy: Inspired the concept for AR-15 mag spring compatibility for Western builders.

Freeman1337: Advised AR-15 mag spring compatible parts; printed and tested mag with AR-15 spring adapted follower and floorplate. Provided images and testing video footage. Gave data on fitment for AR-15 spring compatible parts. 

download

Metrics

Views

3.5K

Project Info

release date

Jun 13, 2022

artifact type

Printable project

library category

Printable Magazines

fabrication method

Primarily Printable

fabrication tool

3D Printer

release country

United States

language

English

license

GNU General Public License v3.0

Firearm Info

type

Rifle

platform

AK-47

caliber

7.62x39

version hash

QmRi1fVwEtwCLBitkev2SZ9MWtpJbKFrzgHQwmfrYHJsNN

files

File Extension
Revo1ution AKM Magazine V1.0.1.zip zip

versions

Version: 1.0.0 latest

Initial release

The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.

Ghost Gunner 3s, GG3s, True Desktop CNC, by Defense Distributed Ghost Gunner 3s, GG3s, True Desktop CNC, by Defense Distributed

Javascript & cookies are required to view this site.