10/22 Tri Cyclone Flash Suppressor
about
10/22 Tri Cyclone Flash Suppressor: FFFTech/FFFTechnology
A flash suppressor with three prongs that slightly angle sideways radially
Printer Used: Monoprice Maker Select Plus
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .18mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5 - 7
Infill: 50%
Infill Pattern: Gyroid
Material Flow: 100%
Hardware Needed:
1x M3x16 Set Screw
SAFETY NOTE: Due to this design coming into contact with hot metal and gasses, it's HIGHLY recommended to print the design, and use Lost PLA Casting in metal for the finished object. The printed version CAN be used, but should not be expected to retain structural rigidity for more than a few dozen rounds fired.
files
| File | Extension |
|---|---|
| 22 Tri Cyclone Flash Suppressor V1.0.2/10-22 Tri Cyclone FS V1.0.2.zip | zip |
versions
Version: 10/22 Tri Cyclone Flash Suppressor V1.0.2 latest
10/22 Tri Cyclone Flash Suppressor V1.0.2: Laffs Dynamics
A flash suppressor with three prongs that slightly angle sideways radially
Update V1.0.2: Changed designer name, changed recommended printer and print settings to the commonly used Ender 3.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .2mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 6
Infill: 100%
Hardware Needed:
1x M3x16 Set Screw
SAFETY NOTE: Due to this design coming into contact with hot metal and gasses, it's HIGHLY recommended to
print the design, and use Lost PLA Casting in metal for the finished object. The printed version CAN be
used, but should not be expected to retain structural rigidity for more than a few dozen rounds fired.
Version: 1.0.0
about
10/22 Tri Cyclone Flash Suppressor: FFFTech/FFFTechnology
A flash suppressor with three prongs that slightly angle sideways radially
Printer Used: Monoprice Maker Select Plus
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .18mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5 - 7
Infill: 50%
Infill Pattern: Gyroid
Material Flow: 100%
Hardware Needed:
1x M3x16 Set Screw
SAFETY NOTE: Due to this design coming into contact with hot metal and gasses, it's HIGHLY recommended to print the design, and use Lost PLA Casting in metal for the finished object. The printed version CAN be used, but should not be expected to retain structural rigidity for more than a few dozen rounds fired.
creator
Metrics
Views
2.1K
Downloads
218
Project Info
release date
Mar 16, 2023
artifact type
library category
fabrication method
release country
United States
language
English
license
files
| File | Extension |
|---|---|
| 22 Tri Cyclone Flash Suppressor V1.0.2/10-22 Tri Cyclone FS V1.0.2.zip | zip |
versions
Version: 10/22 Tri Cyclone Flash Suppressor V1.0.2 latest
10/22 Tri Cyclone Flash Suppressor V1.0.2: Laffs Dynamics
A flash suppressor with three prongs that slightly angle sideways radially
Update V1.0.2: Changed designer name, changed recommended printer and print settings to the commonly used Ender 3.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .2mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 6
Infill: 100%
Hardware Needed:
1x M3x16 Set Screw
SAFETY NOTE: Due to this design coming into contact with hot metal and gasses, it's HIGHLY recommended to
print the design, and use Lost PLA Casting in metal for the finished object. The printed version CAN be
used, but should not be expected to retain structural rigidity for more than a few dozen rounds fired.
Version: 1.0.0
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.
