SlabSlav Flora AKM Mag

about

SlabSlav Flora AKM Mag: Laffs Dynamics

A 30rd AKM mag with overall geometry similar to Slabside Bulgarian mags, with frontal reinforcement ribs similar to the AK-103 mag design. Has a "Flora / Micro Camo" texture pattern on both sides of the magazine. 

Has an anti-friction follower, and a separately printed rear locking lug.

This design ALSO allows the use of AR-15 magazine springs via alternate follower and floorplate versions, for Western (North American countries) builders; as AR-15 magazine springs are often cheaper and easier to acquire. 


Tested with:

 * Palmetto State Armory PSAK-47 GF3, Domestic
 * Zastava ZPAP M70, Serbian Import


Two follower and floorplate versions are available: 

 *Standard: AK spring usage.
 *AR: AR-15 spring usage, labeled on each part. 


Compatible with original Laffs Dynamics Waco Waffle Series AKM Mag parts; with the exception of the baseplate.

 

Printer Used: Ender 3 V2

Filament Used: PLA+

Print Settings:

Extruder: 220C
Bed: 56C 
First Layer Print Height: .2mm 
Standard Layer Height: .16mm
Wall Perimeters: 8+ 
Infill: 45%+
Infill Pattern: Gyroid
Support Material Percentage: 18%

(Use support blockers for the side flora texture patterns.)

 

Hardware Needed:

1x 30rd Length AK Mag Spring

1x 30rd Length AR-15 Mag Spring (OPTIONAL)

 

Parts Installation:

1) Apply cyanoacrylate adhesive inside the pocket for the rear locking lug. If the rear locking lug is slightly loose in the pocket, apply Clear Gorilla Glue instead. 

2) Insert the rear locking lug, with the angled facet facing outwards, and down towards the mag body's base. Wait 24hrs for the previously applied adhesive to cure. 

3) Lightly sand the anti-friction follower's sides and curved spine. 

4) Slide the top of the magazine spring through the front of the follower, above the spring retention tab.

5) Attach the floorplate to the bottom of the magazine spring, making sure the first spring winding snaps over the retainers. 

6) Slide the internal spring assembly into the magazine body.

7) Depress the floorplate, and slide on the baseplate. The floorplate's locking tab must index with the channel in the baseplate. 

 

Notes: 

1) Bulgarian, Korean, and US based Magpul springs have been tested.

2) Bulgarian Slabside Polymer AK mag followers, floorplates, and baseplates are compatible with the SlabSlav series of magazines. 

files

File Extension
SlabSlav Flora AKM Mag.zip zip

versions

Version: 1.0.0 latest

Initial release

about

SlabSlav Flora AKM Mag: Laffs Dynamics

A 30rd AKM mag with overall geometry similar to Slabside Bulgarian mags, with frontal reinforcement ribs similar to the AK-103 mag design. Has a "Flora / Micro Camo" texture pattern on both sides of the magazine. 

Has an anti-friction follower, and a separately printed rear locking lug.

This design ALSO allows the use of AR-15 magazine springs via alternate follower and floorplate versions, for Western (North American countries) builders; as AR-15 magazine springs are often cheaper and easier to acquire. 


Tested with:

 * Palmetto State Armory PSAK-47 GF3, Domestic
 * Zastava ZPAP M70, Serbian Import


Two follower and floorplate versions are available: 

 *Standard: AK spring usage.
 *AR: AR-15 spring usage, labeled on each part. 


Compatible with original Laffs Dynamics Waco Waffle Series AKM Mag parts; with the exception of the baseplate.

 

Printer Used: Ender 3 V2

Filament Used: PLA+

Print Settings:

Extruder: 220C
Bed: 56C 
First Layer Print Height: .2mm 
Standard Layer Height: .16mm
Wall Perimeters: 8+ 
Infill: 45%+
Infill Pattern: Gyroid
Support Material Percentage: 18%

(Use support blockers for the side flora texture patterns.)

 

Hardware Needed:

1x 30rd Length AK Mag Spring

1x 30rd Length AR-15 Mag Spring (OPTIONAL)

 

Parts Installation:

1) Apply cyanoacrylate adhesive inside the pocket for the rear locking lug. If the rear locking lug is slightly loose in the pocket, apply Clear Gorilla Glue instead. 

2) Insert the rear locking lug, with the angled facet facing outwards, and down towards the mag body's base. Wait 24hrs for the previously applied adhesive to cure. 

3) Lightly sand the anti-friction follower's sides and curved spine. 

4) Slide the top of the magazine spring through the front of the follower, above the spring retention tab.

5) Attach the floorplate to the bottom of the magazine spring, making sure the first spring winding snaps over the retainers. 

6) Slide the internal spring assembly into the magazine body.

7) Depress the floorplate, and slide on the baseplate. The floorplate's locking tab must index with the channel in the baseplate. 

 

Notes: 

1) Bulgarian, Korean, and US based Magpul springs have been tested.

2) Bulgarian Slabside Polymer AK mag followers, floorplates, and baseplates are compatible with the SlabSlav series of magazines. 

download

Metrics

Views

1.3K

Downloads

169

Project Info

release date

Jan 31, 2023

artifact type

Printable project

library category

Printable Magazines

fabrication method

Primarily Printable

fabrication tool

3D Printer

release country

United States

language

English

license

Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International

files

File Extension
SlabSlav Flora AKM Mag.zip zip

versions

Version: 1.0.0 latest

Initial release

The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.

Ghost Gunner 3s, GG3s, True Desktop CNC, by Defense Distributed Ghost Gunner 3s, GG3s, True Desktop CNC, by Defense Distributed

Javascript & cookies are required to view this site.