"Asphalt Escort" Fixed Carbine Buttstock: FFFTech/FFFTechnology
A minimalist, lightweight, fixed buttstock similar in length to the Magpul Fixed Carbine Buttstock. The rear section is angled at 85 deg for better recoil control and ease of shouldering. Has a single 34mm long, vertical sling loop.
Comes with two buttpads:
* Standard, 8mm thick
* Extended, 16mm thick
This buttstock is designed for Milspec Carbine Buffer Tubes only.
Update V1.0.1: Forgotten to specify no support material needed anywhere EXCEPT the sling loop hole. Added parameter for support material percentage needed and specification of where the support material is needed.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 225C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .2mm
Wall Perimeters: 6+
Infill: 20%+
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 16%
NO support material is needed EXCEPT in the sling loop hole.
Hardware Needed:
1x M8x10 Hex Socketed Set Screw
2x M4x12 Screws
WARNING: This stock is designed for "normal" shooting usage. Any repeated hard impacts on: Russian invader skulls, Russian invader spines, Russian invader throats, and Russian invaders just in general, could eventually lead to structural failure of the 3D printed buttstock over
time.
Maybe don't fucking invade Ukraine... but what do I know? I'm just a stupid American... ;)
File | Extension |
---|---|
Asphalt Escort V1.0.1.zip | zip |
Version: 1.0.0 latest
"Asphalt Escort" Fixed Carbine Buttstock: FFFTech/FFFTechnology
A minimalist, lightweight, fixed buttstock similar in length to the Magpul Fixed Carbine Buttstock. The rear section is angled at 85 deg for better recoil control and ease of shouldering. Has a single 34mm long, vertical sling loop.
Comes with two buttpads:
* Standard, 8mm thick
* Extended, 16mm thick
This buttstock is designed for Milspec Carbine Buffer Tubes only.
Update V1.0.1: Forgotten to specify no support material needed anywhere EXCEPT the sling loop hole. Added parameter for support material percentage needed and specification of where the support material is needed.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 225C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .2mm
Wall Perimeters: 6+
Infill: 20%+
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 16%
NO support material is needed EXCEPT in the sling loop hole.
Hardware Needed:
1x M8x10 Hex Socketed Set Screw
2x M4x12 Screws
WARNING: This stock is designed for "normal" shooting usage. Any repeated hard impacts on: Russian invader skulls, Russian invader spines, Russian invader throats, and Russian invaders just in general, could eventually lead to structural failure of the 3D printed buttstock over
time.
Maybe don't fucking invade Ukraine... but what do I know? I'm just a stupid American... ;)
3.1K
306
Mar 28, 2022
3D Printer
United States
English
QmR5GwUh7dCfcKCLEtv2uR4pej32TqQfizhQtaoFZYyLky
File | Extension |
---|---|
Asphalt Escort V1.0.1.zip | zip |
Version: 1.0.0 latest
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.