Typhoon Evo Grip (CZ Scorpion Evo 3): FFFTech/FFFTechnology
One of the largest original 3FTech grip designs. (As of June 2022) Has a concave front section with a large swept back backstrap. Swells from 23.6mm thick, out towards the bottom at 30.4mm, with ridges wrapping around the front. Has an internal cross brace running down the entire length of the grip.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 54C
First Layer Print Height: .2mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 25%
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%
Print the grip upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm, so it doesn't stick out the side)
1x M4 Hex Nut
File | Extension |
---|---|
Typhoon Evo Grip V1.2.1.zip | zip |
Version: Typhoon Evo Grip V1.2.1 (CZ Scorpion Evo 3) latest
Typhoon Evo Grip V1.2.1 (CZ Scorpion Evo 3): Laffs Dynamics
One of the largest original Laffs Dynamics grip designs. (As of June 2022) Has a concave front section with a large swept back backstrap. Swells from 23.6mm thick, out towards the bottom at 30.4mm, with ridges wrapping around the front. Has an internal cross brace running down the entire length of the grip.
Update V1.2.1: Reinforced grip mount interface. Updated name of designer.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 54C
First Layer Print Height: .2mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 25%
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%
Print the grip upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm, so it doesn't stick out the side)
1x M4 Hex Nut
Version: 1.0.0
Initial release
Typhoon Evo Grip (CZ Scorpion Evo 3): FFFTech/FFFTechnology
One of the largest original 3FTech grip designs. (As of June 2022) Has a concave front section with a large swept back backstrap. Swells from 23.6mm thick, out towards the bottom at 30.4mm, with ridges wrapping around the front. Has an internal cross brace running down the entire length of the grip.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 54C
First Layer Print Height: .2mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 25%
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%
Print the grip upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm, so it doesn't stick out the side)
1x M4 Hex Nut
2.6K
Jan 04, 2023
3D Printer
United States
English
File | Extension |
---|---|
Typhoon Evo Grip V1.2.1.zip | zip |
Version: Typhoon Evo Grip V1.2.1 (CZ Scorpion Evo 3) latest
Typhoon Evo Grip V1.2.1 (CZ Scorpion Evo 3): Laffs Dynamics
One of the largest original Laffs Dynamics grip designs. (As of June 2022) Has a concave front section with a large swept back backstrap. Swells from 23.6mm thick, out towards the bottom at 30.4mm, with ridges wrapping around the front. Has an internal cross brace running down the entire length of the grip.
Update V1.2.1: Reinforced grip mount interface. Updated name of designer.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 54C
First Layer Print Height: .2mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 25%
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%
Print the grip upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm, so it doesn't stick out the side)
1x M4 Hex Nut
Version: 1.0.0
Initial release
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.