M70 Triangle Skeletal Stock| Model 1
about
M70 Triangle Skeletal Stock, Model 1: Laffs Dynamics
Fixed, triangular buttstock for Yugo/Serbian M70 AK variants.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 7+
Infill: 50%+
Support Material Percentage: 18%
Hardware Needed:
1x M8x30 Bolt, 1mm fine thread pitch (NOT 1.25mm)
1x M8 Washer, 15mm OD (Optional)
2x M4x12mm Screws
files
| File | Extension |
|---|---|
| FBS-1 (Yugo M70).zip | zip |
versions
Version: FBS-1 (Yugo M70) latest
FBS-1 (Yugo M70): Laffs Dynamics
Fixed, triangular buttstock for Yugo/Serbian M70 AK variants.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 7+
Infill: 50%+
Support Material Percentage: 18%
Hardware Needed:
1x M8x30 Bolt, 1mm fine thread pitch (NOT 1.25mm)
1x M8 Washer, 15mm OD (Optional)
2x M4x12mm Screws
Version: 1.0.0
Initial release
about
M70 Triangle Skeletal Stock, Model 1: Laffs Dynamics
Fixed, triangular buttstock for Yugo/Serbian M70 AK variants.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 7+
Infill: 50%+
Support Material Percentage: 18%
Hardware Needed:
1x M8x30 Bolt, 1mm fine thread pitch (NOT 1.25mm)
1x M8 Washer, 15mm OD (Optional)
2x M4x12mm Screws
creator
Metrics
Views
2.6K
Downloads
309
Project Info
release date
Jul 19, 2023
artifact type
library category
fabrication method
fabrication tool
3D Printer
release country
United States
language
English
license
Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International
files
| File | Extension |
|---|---|
| FBS-1 (Yugo M70).zip | zip |
versions
Version: FBS-1 (Yugo M70) latest
FBS-1 (Yugo M70): Laffs Dynamics
Fixed, triangular buttstock for Yugo/Serbian M70 AK variants.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 7+
Infill: 50%+
Support Material Percentage: 18%
Hardware Needed:
1x M8x30 Bolt, 1mm fine thread pitch (NOT 1.25mm)
1x M8 Washer, 15mm OD (Optional)
2x M4x12mm Screws
Version: 1.0.0
Initial release
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.
