AMPoly Series: Single Mag Carriers V1.5.1: FFFTech/FFFTechnology
The first of several designs of the AMPoly Series Mag Carriers. This version features single carriers that can be clipped on/off a standard 1.5in belt, without said belt's removal.
Belt Clips come in two versions:
*Standard
*Thicc
Update 1.5.1: Lancer L5AWM AR-15 magazines have been documented to be compatible with the AR-15 Mag Carrier.
Printer Used: Monoprice Maker Select Plus
Filament Used: PLA+
Print Settings:
Extruder: 208C
Bed: 54C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 4
Infill: 32%
Infill Pattern: Gyroid
Material Flow: 100%
Adhesive Used: Clear Gorilla Glue (Not Superglue)
Assembly Directions:
1) Use sandpaper to roughen the tabs of the belt clip.
2) Apply Clear Gorilla Glue to the tab index slots of the mag carrier.
3) Clamp the belt clip to the carrier. Be sure the clip is parallel to the side of the carrier.
4) Wipe away adhesive squeeze-out.
5) Let the adhesive set for 2 hours clamped. Full cure time 24 hours. (But after the 2, I doesn't need to be clamped.)
Notes:
Note 1) The AMPoly Series is designed for Magpul and Lancer L5AWM AR-15 mags, and double stack Glock mags. (Glock mag carrier tested with Glock OEM, Magpul, and KCI mags.)
Note 2) The use of Clear Gorilla Glue was chosen to reduce design weight and hardware usage. (Basically no screws needed) From testing, the plastic clips will snap before the bond to the carrier fails, should the adhesive be applied properly.
File | Extension |
---|---|
AMPoly Single Mag Carrier V1.5.1.zip | zip |
Version: 1.0.0 latest
AMPoly Series: Single Mag Carriers V1.5.1: FFFTech/FFFTechnology
The first of several designs of the AMPoly Series Mag Carriers. This version features single carriers that can be clipped on/off a standard 1.5in belt, without said belt's removal.
Belt Clips come in two versions:
*Standard
*Thicc
Update 1.5.1: Lancer L5AWM AR-15 magazines have been documented to be compatible with the AR-15 Mag Carrier.
Printer Used: Monoprice Maker Select Plus
Filament Used: PLA+
Print Settings:
Extruder: 208C
Bed: 54C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 4
Infill: 32%
Infill Pattern: Gyroid
Material Flow: 100%
Adhesive Used: Clear Gorilla Glue (Not Superglue)
Assembly Directions:
1) Use sandpaper to roughen the tabs of the belt clip.
2) Apply Clear Gorilla Glue to the tab index slots of the mag carrier.
3) Clamp the belt clip to the carrier. Be sure the clip is parallel to the side of the carrier.
4) Wipe away adhesive squeeze-out.
5) Let the adhesive set for 2 hours clamped. Full cure time 24 hours. (But after the 2, I doesn't need to be clamped.)
Notes:
Note 1) The AMPoly Series is designed for Magpul and Lancer L5AWM AR-15 mags, and double stack Glock mags. (Glock mag carrier tested with Glock OEM, Magpul, and KCI mags.)
Note 2) The use of Clear Gorilla Glue was chosen to reduce design weight and hardware usage. (Basically no screws needed) From testing, the plastic clips will snap before the bond to the carrier fails, should the adhesive be applied properly.
5.5K
Dec 17, 2021
United States
English
QmS1fsTCRWurTndB8j57WgNpwUQ3SbNrePUYf52Meiv9AM
File | Extension |
---|---|
AMPoly Single Mag Carrier V1.5.1.zip | zip |
Version: 1.0.0 latest
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.