Yeet22 V.3

about

This isn't a full release since documentation is unfinished and assembly is quite similar to v2/

Here's a list of changes:

- Additional spring is now required for the trigger. It can be slightly softer than the spring

  that pushes sliding block/fc slider.

- Mag catch is changed and thus requires different spring (3-4mm ID, <=5mm OD).

- Different magazine. V3 takes extended capacity P17 mags - these are being developed by 

  plcky_shdw, beta channel can be found on Deterrence Dispensed chat. Files for this magazine are not included

  and can only be sourced there.

- Sight slab and adjustable sights are no longer a thing.

- Magnetic delay isn't a thing anymore either.

- No more different frames for different barrels. 16mm OD Shim for 8mm OD liner is included and it can be 

  drilled out to any diameter up to 14mm.

- Experimental suppressor file added. This thing is untested and under any circumstances shouldn't be used

  with smoothbore barrel.

 

Some general advice:

 

Supports are still pain in the ass to remove, so your settings should be tuned precisely for easy removal.

I'd recommend to set support overhang angle at 70-75 degrees and use support blockers liberally.

For rifling, ideal tube ID would be 5.45mm. If it's 5.45 or wider, do not bore it any further. It's best to do 

the chambering with 5.7-5.8mm reamer before rifling. Under ideal conditions, chambered bullet should touch or even 

dig in into the grooves.

If it's too hard to push mandrel into the tube, reprint it with negative 0,04-0,06mm horizontal expansion.

files

File Extension
YEET22 V.3 02-28.zip zip

versions

Version: 1.0.0 latest

initial upload

about

This isn't a full release since documentation is unfinished and assembly is quite similar to v2/

Here's a list of changes:

- Additional spring is now required for the trigger. It can be slightly softer than the spring

  that pushes sliding block/fc slider.

- Mag catch is changed and thus requires different spring (3-4mm ID, <=5mm OD).

- Different magazine. V3 takes extended capacity P17 mags - these are being developed by 

  plcky_shdw, beta channel can be found on Deterrence Dispensed chat. Files for this magazine are not included

  and can only be sourced there.

- Sight slab and adjustable sights are no longer a thing.

- Magnetic delay isn't a thing anymore either.

- No more different frames for different barrels. 16mm OD Shim for 8mm OD liner is included and it can be 

  drilled out to any diameter up to 14mm.

- Experimental suppressor file added. This thing is untested and under any circumstances shouldn't be used

  with smoothbore barrel.

 

Some general advice:

 

Supports are still pain in the ass to remove, so your settings should be tuned precisely for easy removal.

I'd recommend to set support overhang angle at 70-75 degrees and use support blockers liberally.

For rifling, ideal tube ID would be 5.45mm. If it's 5.45 or wider, do not bore it any further. It's best to do 

the chambering with 5.7-5.8mm reamer before rifling. Under ideal conditions, chambered bullet should touch or even 

dig in into the grooves.

If it's too hard to push mandrel into the tube, reprint it with negative 0,04-0,06mm horizontal expansion.

Download

Metrics

Views

4.3K

Downloads

118

Project Info

release date

Mar 16, 2023

artifact type

Printable project

library category

Printable Firearms

fabrication method

Primarily Printable

fabrication tool

3D Printer

release country

United States

language

English

license

No license

Firearm Info

type

Pistol

platform

YEET22

caliber

.22LR

files

File Extension
YEET22 V.3 02-28.zip zip

versions

Version: 1.0.0 latest

initial upload

The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.

Ghost Gunner 3s, GG3s, True Desktop CNC, by Defense Distributed Ghost Gunner 3s, GG3s, True Desktop CNC, by Defense Distributed

Javascript & cookies are required to view this site.