Apperently my content is getting to spicy for youtube. I have the video back up on Odysee
https://odysee.com/@SmallTeamSupply:6/next-gen-3d-printed-lower-odysee:3
This 3d printable AR-15 lower bridges the common failure point (through the rear take down pin) by using #10 5" wood deck screws to distribute the load/shock around it.
These lowers have passed a rigorous 3 day field training exercise using the M.I.L.E.S. engagement system at the One Shepherd Leadership Instutue, as well as square range testing; malfunction clearing via mortering and firing ball ammunition.
Recommended filament: Taulman3d PCTPE with plently of brim and supports to keep it from warping and peeling off the build plate. Print at 243C, slowly and be sure to use glue to hold it down. If you are using a magnetic build plate be sure to clip it down near the print. This stuff must be dryed throughly before using it, throw it in a filament dryer at 65C for atleast 3 days before printing with it and keep it in there while using it.
Recommended Print Orientation: 45 Deg
Additonal parts required:
Qty 2) #10 5" wood deck screws
Qty 1) #6 1" wood screw
Qty 1) Threaded insert - E-Z LOK HI-428-WH
Small Team Supply fixed stock or endplate is also needed to complete
Note: Most holes will need to be chased by using common size drill bits but a long 1/8" drill bit may be needed for chasing the rear take down pin detent pin hole.
File | Extension |
---|---|
Smallteamsupply ar15 lower reciever V1.3 release.STEP | unknown |
Smallteamsupply ar15 lower reciever V1.3 release.STL | STL |
Version: V1.3 Updated Magwell latest
Update to Magwell for easier insertion and allows Schmeisser S60 magazines to seat.
Version: 1.0.0
First public release
Apperently my content is getting to spicy for youtube. I have the video back up on Odysee
https://odysee.com/@SmallTeamSupply:6/next-gen-3d-printed-lower-odysee:3
This 3d printable AR-15 lower bridges the common failure point (through the rear take down pin) by using #10 5" wood deck screws to distribute the load/shock around it.
These lowers have passed a rigorous 3 day field training exercise using the M.I.L.E.S. engagement system at the One Shepherd Leadership Instutue, as well as square range testing; malfunction clearing via mortering and firing ball ammunition.
Recommended filament: Taulman3d PCTPE with plently of brim and supports to keep it from warping and peeling off the build plate. Print at 243C, slowly and be sure to use glue to hold it down. If you are using a magnetic build plate be sure to clip it down near the print. This stuff must be dryed throughly before using it, throw it in a filament dryer at 65C for atleast 3 days before printing with it and keep it in there while using it.
Recommended Print Orientation: 45 Deg
Additonal parts required:
Qty 2) #10 5" wood deck screws
Qty 1) #6 1" wood screw
Qty 1) Threaded insert - E-Z LOK HI-428-WH
Small Team Supply fixed stock or endplate is also needed to complete
Note: Most holes will need to be chased by using common size drill bits but a long 1/8" drill bit may be needed for chasing the rear take down pin detent pin hole.
9.9K
698
May 03, 2022
3D Printer
United States
English
Creative Commons Attribution-NonCommercial 4.0 International
QmQ6satvNmE8Lj74EnbnqP1j97vsjXRuP2vizeJ5LjjuoP
File | Extension |
---|---|
Smallteamsupply ar15 lower reciever V1.3 release.STEP | unknown |
Smallteamsupply ar15 lower reciever V1.3 release.STL | STL |
Version: V1.3 Updated Magwell latest
Update to Magwell for easier insertion and allows Schmeisser S60 magazines to seat.
Version: 1.0.0
First public release
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.