"Between the Ribs" Push Dagger: FFFTech/FFFTechnology
An offset T-handle push dagger with a double edged blade. One side transitions from a straight
edge, then slopes forwards towards the tip. The other side is a straight blade with a wide tanto
styled tip.
This slender design is suited for reaching organs between and under the rib cage.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .18mm
Standard Layer Height: .12mm
Wall Thickness: .40
Wall Perimeters: 8+
Infill: 50%+
Infill Pattern: Gyroid
Material Flow: 100%
Note: Due to this specific push dagger's slim design, it's HIGHLY recommended to print with at LEAST 8+ walls for best durability within it's intended design parameters.
File | Extension |
---|---|
Between the Ribs Push Dagger V1.0.1.zip | zip |
Version: "Between the Ribs" Push Dagger V1.0.1 latest
"Between the Ribs" Push Dagger V1.0.1: Laffs Dynamics
An offset T-handle push dagger with a double edged blade. One side transitions from a straight edge, then slopes forwards towards the tip. The other side is a straight blade with a wide tanto styled tip.
This slender design is suited for reaching organs between and under the rib cage.
Update V1.0.1: Changed recommended print settings for better device strength, updated name of designer.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .12mm
Wall Thickness: .40
Wall Perimeters: 8+
Infill: 50%+
Note: Due to this specific push dagger's slim design, it's HIGHLY recommended to print with at LEAST 8+ walls for best durability within it's intended design parameters.
Version: 1.0.0
Initial release
"Between the Ribs" Push Dagger: FFFTech/FFFTechnology
An offset T-handle push dagger with a double edged blade. One side transitions from a straight
edge, then slopes forwards towards the tip. The other side is a straight blade with a wide tanto
styled tip.
This slender design is suited for reaching organs between and under the rib cage.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .18mm
Standard Layer Height: .12mm
Wall Thickness: .40
Wall Perimeters: 8+
Infill: 50%+
Infill Pattern: Gyroid
Material Flow: 100%
Note: Due to this specific push dagger's slim design, it's HIGHLY recommended to print with at LEAST 8+ walls for best durability within it's intended design parameters.
4.2K
Jan 04, 2023
3D Printer
United States
English
File | Extension |
---|---|
Between the Ribs Push Dagger V1.0.1.zip | zip |
Version: "Between the Ribs" Push Dagger V1.0.1 latest
"Between the Ribs" Push Dagger V1.0.1: Laffs Dynamics
An offset T-handle push dagger with a double edged blade. One side transitions from a straight edge, then slopes forwards towards the tip. The other side is a straight blade with a wide tanto styled tip.
This slender design is suited for reaching organs between and under the rib cage.
Update V1.0.1: Changed recommended print settings for better device strength, updated name of designer.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .12mm
Wall Thickness: .40
Wall Perimeters: 8+
Infill: 50%+
Note: Due to this specific push dagger's slim design, it's HIGHLY recommended to print with at LEAST 8+ walls for best durability within it's intended design parameters.
Version: 1.0.0
Initial release
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.