Glock 17 Picatinny Adaptor Rail

Purchase high-quality prints of Laffs Dynamics designs at avesrails.com

about

Glock 17 Picatinny Adaptor Rail by FFFTech/FFFTechnology

Compatible with Gen 4 Glock 17 frames, as well as Glock models that share the same frame such as: Glock 17L, 22, 31, 34, 35 and 37.

A six slotted picatinny rail that attaches to the Glock 17 proprietary rail. While most picatinny compatible accessories will fit on the glock rail, the single slot limits the options when one wishes to move accessories forward and back on the rail. Should one wish to turn their Glock into an SBR, the adaptor is long enough (and has enough slots) to facilitate a foregrip. The rail extends all the way to the front of the triggerguard, and the front protrudes only slightly, being flush with the front of the slide.

Printer Used: Monoprice Maker Select Plus

Filament Used: PLA+

Print Settings:

Extruder: 204C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 3
Infill: 25%
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 10%

Support material only for the rail slots directly above the print bed.

Hardware Needed:

1x M4x10mm Hex Socketed Set Screw

Installation:

1) After support material removal, slide the picatinny adaptor over the Glock Rail.

2) Hold the rail to it's rearmost position and start threading the set screw into the adaptor.

3) Drive the set screw flush with the bottom of rail slot. Check every 2 screw revolutions to see if the rail adaptor is properly secure.

4) Once secure, attach dem bomb diggity accessories.

files

File Extension
Glock 17 Picatinny Adaptor Rail.zip zip

versions

Version: V1.5 latest

Glock 17 Picatinny Adaptor Rail V1.5 by FFFTech/FFFTechnology

The following description is for V1.5, but the files for V1 are still included in the .zip file, with V1.5 files as well.

Compatible with Gen 3 & Gen 4 Glock 17 frames, as well as Glock models that share the same frame such as: Glock 17L, 22, 31, 34, 35 and 37.

An updated design of the original Glock 17 Picatinny Adaptor Rail. Unneeded material has been removed from the internal structure, the edges of the picatinny rail channels have been scalloped, and overall height has been reduced by 1mm. Overall takes a few minutes less time to print, and needs a little material than the previous design.

Printer Used: Monoprice Maker Select Plus

Filament Used: PLA+

Print Settings:

Extruder: 204C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 3
Infill: 25%
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 10%

Support material only for the rail slots directly above the print bed.

Hardware Needed:

1x M4x10mm Hex Socketed Set Screw

Installation:

1) After support material removal, slide the picatinny adaptor over the Glock Rail.

2) Hold the rail to it's rearmost position and start threading the set screw into the adaptor.

3) Drive the set screw flush with the bottom of rail slot. Check every 2 screw revolutions to see if the rail adaptor is properly secure.

4) Once secure, attach dem bomb diggity accessories.

Version: 1.0.0

Initial release

about

Purchase high-quality prints of Laffs Dynamics designs at avesrails.com

Glock 17 Picatinny Adaptor Rail by FFFTech/FFFTechnology

Compatible with Gen 4 Glock 17 frames, as well as Glock models that share the same frame such as: Glock 17L, 22, 31, 34, 35 and 37.

A six slotted picatinny rail that attaches to the Glock 17 proprietary rail. While most picatinny compatible accessories will fit on the glock rail, the single slot limits the options when one wishes to move accessories forward and back on the rail. Should one wish to turn their Glock into an SBR, the adaptor is long enough (and has enough slots) to facilitate a foregrip. The rail extends all the way to the front of the triggerguard, and the front protrudes only slightly, being flush with the front of the slide.

Printer Used: Monoprice Maker Select Plus

Filament Used: PLA+

Print Settings:

Extruder: 204C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 3
Infill: 25%
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 10%

Support material only for the rail slots directly above the print bed.

Hardware Needed:

1x M4x10mm Hex Socketed Set Screw

Installation:

1) After support material removal, slide the picatinny adaptor over the Glock Rail.

2) Hold the rail to it's rearmost position and start threading the set screw into the adaptor.

3) Drive the set screw flush with the bottom of rail slot. Check every 2 screw revolutions to see if the rail adaptor is properly secure.

4) Once secure, attach dem bomb diggity accessories.

Download

Metrics

Views

6K

Downloads

623

Project Info

release date

Jul 02, 2021

artifact type

Printable project

library category

Printable Peripherals / Parts

fabrication method

Primarily Printable

release country

United States

language

English

license

GNU General Public License v3.0

Firearm Info

type

Pistol

platform

Glock 17

part

Rail

version hash

QmVPyFtZj7j12Leuu8Hb2GMzNt3TCpy5JAqNHqFFbbkKBg

files

File Extension
Glock 17 Picatinny Adaptor Rail.zip zip

versions

Version: V1.5 latest

Glock 17 Picatinny Adaptor Rail V1.5 by FFFTech/FFFTechnology

The following description is for V1.5, but the files for V1 are still included in the .zip file, with V1.5 files as well.

Compatible with Gen 3 & Gen 4 Glock 17 frames, as well as Glock models that share the same frame such as: Glock 17L, 22, 31, 34, 35 and 37.

An updated design of the original Glock 17 Picatinny Adaptor Rail. Unneeded material has been removed from the internal structure, the edges of the picatinny rail channels have been scalloped, and overall height has been reduced by 1mm. Overall takes a few minutes less time to print, and needs a little material than the previous design.

Printer Used: Monoprice Maker Select Plus

Filament Used: PLA+

Print Settings:

Extruder: 204C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 3
Infill: 25%
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 10%

Support material only for the rail slots directly above the print bed.

Hardware Needed:

1x M4x10mm Hex Socketed Set Screw

Installation:

1) After support material removal, slide the picatinny adaptor over the Glock Rail.

2) Hold the rail to it's rearmost position and start threading the set screw into the adaptor.

3) Drive the set screw flush with the bottom of rail slot. Check every 2 screw revolutions to see if the rail adaptor is properly secure.

4) Once secure, attach dem bomb diggity accessories.

Version: 1.0.0

Initial release

The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.

Ghost Gunner 3s, GG3s, True Desktop CNC, by Defense Distributed Ghost Gunner 3s, GG3s, True Desktop CNC, by Defense Distributed

Javascript & cookies are required to view this site.