The Hackbolt is a combination between the U-Bolt Vanguard and the Hellfire.
There are two versions: The Hackbolt, a plain version just like the U-Bolt and the Hackbolt STEPN'T which is for those who prefer meme lowers. Of course, STEP files are included should you decide to add your own graphics.
Contains updated versions of the Hellfire's pivot pin plates that are compatible with both the Hellfire and the Hackbolt.
The main benefits are that:
It is universally compatible. The U-Bolt Vanguard is not compatible with my hand-guard nor a small selection of others, but this is.
The design of the Hellfire's front plates should hold up better than the U-Bolt simply due to print orientation.
Should the plates fail, they are easily and quickly replaced, unlike the U-Bolt.
More color customization.
https://imgur.com/a/CreOTZt for more photos.
UPDATE 4-17-2021:
Revised mag well to now have tighter tolerances. Should eliminate the slight mag rotation that was occurring. Tested with Gen3 PMAGS. They still drop free. If yours don't, then take a file/sand paper to the front of the mag well interior.
Switched over to a low shelf to accommodate more room for Skittles.
Lower:
0.15mm layerheight
6 wall count
98-100% infill (cubic, concentric, gyroid, zig-zag)
Tree Supports
Adhesion - Brim
Plates:
0.15mm layer height
6 wall count
90-100% infill
No supports
Adhesion - Skirt/None
Screws:
0.15mm layer height
6 wall count
80-100% infill
No supports
Adhesion - Skirt/None
Screw Tool:
0.15mm layer height
2-6 wall count
60-100% infill
No supports
Adhesion - Skirt/None
Adjust as you see fit.
File | Extension |
---|---|
Hackbolt.zip | zip |
Version: 1.0.0 latest
Initial release
The Hackbolt is a combination between the U-Bolt Vanguard and the Hellfire.
There are two versions: The Hackbolt, a plain version just like the U-Bolt and the Hackbolt STEPN'T which is for those who prefer meme lowers. Of course, STEP files are included should you decide to add your own graphics.
Contains updated versions of the Hellfire's pivot pin plates that are compatible with both the Hellfire and the Hackbolt.
The main benefits are that:
It is universally compatible. The U-Bolt Vanguard is not compatible with my hand-guard nor a small selection of others, but this is.
The design of the Hellfire's front plates should hold up better than the U-Bolt simply due to print orientation.
Should the plates fail, they are easily and quickly replaced, unlike the U-Bolt.
More color customization.
https://imgur.com/a/CreOTZt for more photos.
UPDATE 4-17-2021:
Revised mag well to now have tighter tolerances. Should eliminate the slight mag rotation that was occurring. Tested with Gen3 PMAGS. They still drop free. If yours don't, then take a file/sand paper to the front of the mag well interior.
Switched over to a low shelf to accommodate more room for Skittles.
Lower:
0.15mm layerheight
6 wall count
98-100% infill (cubic, concentric, gyroid, zig-zag)
Tree Supports
Adhesion - Brim
Plates:
0.15mm layer height
6 wall count
90-100% infill
No supports
Adhesion - Skirt/None
Screws:
0.15mm layer height
6 wall count
80-100% infill
No supports
Adhesion - Skirt/None
Screw Tool:
0.15mm layer height
2-6 wall count
60-100% infill
No supports
Adhesion - Skirt/None
Adjust as you see fit.
1.4K
Mar 31, 2021
3D Printer
United States
English
No license
QmNqqug8QxdtT4oFeasDkvAsP7vM2Jz9h1FaSnEc767st5
File | Extension |
---|---|
Hackbolt.zip | zip |
Version: 1.0.0 latest
Initial release
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.