Henry Husher: A Henry H001 Suppressor

about

Henry Husher: A Henry H001 Suppressor
Original Developer: nameisnight

The goal of the project is to make a suppressor for the Henry H001 that does not need any modification to the gun and keeps the original magaizne tube usable while attached.

Needed Hardware:
    2 x M3x20mm Screws
    2 x M3 Nuts
    1 x 9.8x2.4mm (P10A) O-Ring - OPTINAL
    
Files to print:
    1 x Suppressor Type (A or B)
    1 x Barrel Band Type (A or B)

Print Settings:
    PLA+ or Better
    210c Hotend
    55c Bed
    .20 layer hight
    Minimum 3 Walls
    Max infill (Has been tested with 5.5% gyroid without issue...)
    Supports on build plate only

Assembly:
    1. Remove Outer Magazine Tube.
    2. Place an O-ring in the suppressor where the barrel will interface.
    3. Carfully slide suppressor onto barrel with the smaller bottom part between the barrel and the magazine tube, Make sure its pressed on the O-ring.
    4. Put M3 nuts into the left and right slots of the suppressor and place the barrel band over the barrel, Put the M3x20mm screws through the barrel band and screw them into the nuts on the suppressor.
    5. Tighten the mounting screws with even pressure.
    6. Replace Outer Magazine Tube.

Warnings:
    This is a NFA item. Know your laws!
    Check for cracks often, If ANY are found despose of suppressor and make a new one.
    Don't use hypersonic ammunition!

NOTES:
    The barrel mockup is not to spec! This is an example of how to mount the suppressor. Visual only.
    The file "H001 Suppressor Mount Only" is the CAD of the mount up to where the barrel of the gun meets the device, to allow the user to make custom baffles, bodies, etc.
    Barrel Bands and Suppressor Types are interchangable, The Suppressors are the same otherthen baffle design. Barrel bands have a different pressure point for mounting and support the O-ring better.
    Use Blue Locktight on the mounting screws to help keep them from backing out.
    Alternitively, you can use a 8.8x1.9MM (P9) O-Ring as it will allow a more 'flush' barrel interface while. But will offer less then perfect gas seal.
    Sub-Sonic Ammo recommended, Standard Voloicty acceptable.

files

File Extension
Henry Husher.zip zip

versions

Version: 1.0.0 latest

Initial release

about

Henry Husher: A Henry H001 Suppressor
Original Developer: nameisnight

The goal of the project is to make a suppressor for the Henry H001 that does not need any modification to the gun and keeps the original magaizne tube usable while attached.

Needed Hardware:
    2 x M3x20mm Screws
    2 x M3 Nuts
    1 x 9.8x2.4mm (P10A) O-Ring - OPTINAL
    
Files to print:
    1 x Suppressor Type (A or B)
    1 x Barrel Band Type (A or B)

Print Settings:
    PLA+ or Better
    210c Hotend
    55c Bed
    .20 layer hight
    Minimum 3 Walls
    Max infill (Has been tested with 5.5% gyroid without issue...)
    Supports on build plate only

Assembly:
    1. Remove Outer Magazine Tube.
    2. Place an O-ring in the suppressor where the barrel will interface.
    3. Carfully slide suppressor onto barrel with the smaller bottom part between the barrel and the magazine tube, Make sure its pressed on the O-ring.
    4. Put M3 nuts into the left and right slots of the suppressor and place the barrel band over the barrel, Put the M3x20mm screws through the barrel band and screw them into the nuts on the suppressor.
    5. Tighten the mounting screws with even pressure.
    6. Replace Outer Magazine Tube.

Warnings:
    This is a NFA item. Know your laws!
    Check for cracks often, If ANY are found despose of suppressor and make a new one.
    Don't use hypersonic ammunition!

NOTES:
    The barrel mockup is not to spec! This is an example of how to mount the suppressor. Visual only.
    The file "H001 Suppressor Mount Only" is the CAD of the mount up to where the barrel of the gun meets the device, to allow the user to make custom baffles, bodies, etc.
    Barrel Bands and Suppressor Types are interchangable, The Suppressors are the same otherthen baffle design. Barrel bands have a different pressure point for mounting and support the O-ring better.
    Use Blue Locktight on the mounting screws to help keep them from backing out.
    Alternitively, you can use a 8.8x1.9MM (P9) O-Ring as it will allow a more 'flush' barrel interface while. But will offer less then perfect gas seal.
    Sub-Sonic Ammo recommended, Standard Voloicty acceptable.

Download

creator

Metrics

Views

3.3K

Downloads

234

Project Info

release date

Dec 14, 2022

artifact types

CAD Object, Printable project

library category

Printable Peripherals / Parts

fabrication method

Primarily Printable

fabrication tool

3D Printer

release country

United States

language

English

license

No license

files

File Extension
Henry Husher.zip zip

versions

Version: 1.0.0 latest

Initial release

The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.

Ghost Gunner 3s, GG3s, True Desktop CNC, by Defense Distributed Ghost Gunner 3s, GG3s, True Desktop CNC, by Defense Distributed

Javascript & cookies are required to view this site.