Phobos AR-15 Lower Receiver
Version 1.2
Changelog
- Added cut to Buffer Tower to allow use of Forward Assist without modification of lower 2 Adjusted takedown pin through holes to proper location at rear.
Description
This design is intially inspired from the vanguard by Shadowfall. Special thanks to JT for improvements and testing. So what happens when you take most of the magazine well away from an AR-15? Turns out, not a bloody thing. It feeds and functions flawlessly, with the magazine being perfectly stable even when beat on. With the almost FAL look to the magazine well, its sexy, light, and most importantly, has been tested past 2000 rounds with a standard 5.56 upper. It has been tested with Magpul PMAG's and Aluminium GI mags without failure. Magazines drop free.
Printing Instructions
Print Phobos_V1.2.STL if printer is capable of the size. Print vertically for greatest strength. Print side to side only if Z axis incapable of sufficient height. Acetone treatment after printing recommended after vertical printing, required after side to side printing. Phobos_V1.2_Front.STL should be printed Vertically, Phobos_V1.2_Rear.STL should be printed back to front. Acetone welding will be required to bond the two parts, and acetone treatment will be required post-welding to ensure adequate strength.
Notes For comments, concerns, and questions, go to www.fosscad.org/fc/chat
File | Extension |
---|---|
README.md | md |
Phobos_V1.2_Rear.stl | stl |
Phobos_V1.2_Rear.step | step |
Phobos_V1.2_Rear.sldprt | sldprt |
Phobos_V1.2_Front.stl | stl |
Phobos_V1.2_Front.step | step |
Phobos_V1.2_Front.sldprt | sldprt |
Phobos_V1.2.stl | stl |
Phobos_V1.2.step | step |
Phobos_V1.2.sldprt | sldprt |
Version: 1.0.0 latest
initial upload
Phobos AR-15 Lower Receiver
Version 1.2
Changelog
- Added cut to Buffer Tower to allow use of Forward Assist without modification of lower 2 Adjusted takedown pin through holes to proper location at rear.
Description
This design is intially inspired from the vanguard by Shadowfall. Special thanks to JT for improvements and testing. So what happens when you take most of the magazine well away from an AR-15? Turns out, not a bloody thing. It feeds and functions flawlessly, with the magazine being perfectly stable even when beat on. With the almost FAL look to the magazine well, its sexy, light, and most importantly, has been tested past 2000 rounds with a standard 5.56 upper. It has been tested with Magpul PMAG's and Aluminium GI mags without failure. Magazines drop free.
Printing Instructions
Print Phobos_V1.2.STL if printer is capable of the size. Print vertically for greatest strength. Print side to side only if Z axis incapable of sufficient height. Acetone treatment after printing recommended after vertical printing, required after side to side printing. Phobos_V1.2_Front.STL should be printed Vertically, Phobos_V1.2_Rear.STL should be printed back to front. Acetone welding will be required to bond the two parts, and acetone treatment will be required post-welding to ensure adequate strength.
Notes For comments, concerns, and questions, go to www.fosscad.org/fc/chat
2.1K
191
Oct 19, 2023
3D Printer
United States
English
No license
File | Extension |
---|---|
README.md | md |
Phobos_V1.2_Rear.stl | stl |
Phobos_V1.2_Rear.step | step |
Phobos_V1.2_Rear.sldprt | sldprt |
Phobos_V1.2_Front.stl | stl |
Phobos_V1.2_Front.step | step |
Phobos_V1.2_Front.sldprt | sldprt |
Phobos_V1.2.stl | stl |
Phobos_V1.2.step | step |
Phobos_V1.2.sldprt | sldprt |
Version: 1.0.0 latest
initial upload
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.