Random Surprise Taco Grips (AR-15): FFFTech/FFFTechnology
Geezus CHRIST what have I done?!?! I downed the whole bottle of Russian silly water, and now it appears I pulled another grip design right out my ass! (Damnit! I forgot to wipe...) I don't have a designation, nor official project name for this, sooooooooo...
These are the OFFICIAL 3FTech "Random Surprise Taco Grips"... Yayyyyyyyyyyyyyy!
Oh shit, it seems I went overboard and made SIX friggin variants:
*Standard
*Ridged (I will never call it ribbed! *Fuck I just did*)
*Skewed Squares (Hey that's what everything looked like last night!)
*Arches
*Reverse Grip Paneled
*Gamma Burst (Oh shit, screwdriver slipped off the Demon Core again...)
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 25%
Infill Pattern: Gyroid
Material Flow: 100.25%
Support Material Percentage: 18%
Print the grip upside - down.
Hardware Needed:
1x Allen Head Screw, 1/4-28 x 1"
1x Steel Star Washer
1x Safety Selector Detent Pin
1x Safety Selector Detent Spring
Don't read into the name too much.
File | Extension |
---|---|
Random Surprise Taco Grips.zip | zip |
Version: 1.0.0 latest
Random Surprise Taco Grips (AR-15): FFFTech/FFFTechnology
Geezus CHRIST what have I done?!?! I downed the whole bottle of Russian silly water, and now it appears I pulled another grip design right out my ass! (Damnit! I forgot to wipe...) I don't have a designation, nor official project name for this, sooooooooo...
These are the OFFICIAL 3FTech "Random Surprise Taco Grips"... Yayyyyyyyyyyyyyy!
Oh shit, it seems I went overboard and made SIX friggin variants:
*Standard
*Ridged (I will never call it ribbed! *Fuck I just did*)
*Skewed Squares (Hey that's what everything looked like last night!)
*Arches
*Reverse Grip Paneled
*Gamma Burst (Oh shit, screwdriver slipped off the Demon Core again...)
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 25%
Infill Pattern: Gyroid
Material Flow: 100.25%
Support Material Percentage: 18%
Print the grip upside - down.
Hardware Needed:
1x Allen Head Screw, 1/4-28 x 1"
1x Steel Star Washer
1x Safety Selector Detent Pin
1x Safety Selector Detent Spring
Don't read into the name too much.
1.6K
Mar 14, 2022
3D Printer
United States
English
QmSiDaM75cJ1fY5nF2rreZrzvpJohe8YTzTv1TFow2yvk6
File | Extension |
---|---|
Random Surprise Taco Grips.zip | zip |
Version: 1.0.0 latest
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.