RDR T1 V1.0.2: FFFTech/FFFTechnology
A set of basic risers for red dot optics that use the common Aimpoint T1 mounting footprint. The +15mm to +25mm risers have a hollow section through their bodies to allow for use of iron sights.
Six risers are available: (READ NOTES)
* Standard Mount
* +5mm
* +10mm
* +15mm
* +20mm
* +25mm
Update V1.0.2: The number of parts under "hardware" was previously incorrect; stating only needing one of each part. The correct amount is two of each part.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .12mm
Wall Thickness: .40mm
Wall Perimeters: 6+
Infill: 25%+
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%
Print the mount/riser upside-down
Hardware Needed:
2x M5x30 Hex Socketed Machine Screw/Bolt
2x M5 Hex Nut (Be sure both bolt & nut are the same thread pitch.)
Notes:
1) The height of the Standard mount is (from the top of the picatinny rail to the bottom of the red dot's mounting surface) is5.53mm. That means if you attach the +20mm riser, it's actual height is 25.53mm. The millimeter designations for the risers are based on the addition to the Standard mount's height, not the riser's height itself.
File | Extension |
---|---|
RDR T1 V1.0.2.zip | zip |
Version: 1.0.0 latest
RDR T1 V1.0.2: FFFTech/FFFTechnology
A set of basic risers for red dot optics that use the common Aimpoint T1 mounting footprint. The +15mm to +25mm risers have a hollow section through their bodies to allow for use of iron sights.
Six risers are available: (READ NOTES)
* Standard Mount
* +5mm
* +10mm
* +15mm
* +20mm
* +25mm
Update V1.0.2: The number of parts under "hardware" was previously incorrect; stating only needing one of each part. The correct amount is two of each part.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .12mm
Wall Thickness: .40mm
Wall Perimeters: 6+
Infill: 25%+
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%
Print the mount/riser upside-down
Hardware Needed:
2x M5x30 Hex Socketed Machine Screw/Bolt
2x M5 Hex Nut (Be sure both bolt & nut are the same thread pitch.)
Notes:
1) The height of the Standard mount is (from the top of the picatinny rail to the bottom of the red dot's mounting surface) is5.53mm. That means if you attach the +20mm riser, it's actual height is 25.53mm. The millimeter designations for the risers are based on the addition to the Standard mount's height, not the riser's height itself.
2.3K
333
Jun 20, 2022
3D Printer
United States
English
QmPn9pUnFkFHRD6vK1Cq6v81WR78WVUh7B6yQ8qYvke6JY
File | Extension |
---|---|
RDR T1 V1.0.2.zip | zip |
Version: 1.0.0 latest
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.