South Slav Buttstock (Yugo M70 AK)
about
ABS-1 (Yugo M70 AK): Laffs Dynamics
A hybrid design; the simplicity of a sliding wire buttstock, without the dogshit cheekweld that comes with them. Collapses down to 177mm/6.9in in length.
To extend the buttstock, simply pull back until the locking bar indexes with the corresponding notches in the 6mm rods. Vice versa, press the locking bar actuator in, and press forwards on the butt.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 32%+
Material Flow: 100%
Support Material Percentage: 16%
Print Orientations:
*Buttstock: Buttpad, down.
*Stock Mount: Widest, flattest facet, down.
*Locking Mech Mount: Front, non-angled facet down; Laffs logo upwards.
*Locking Actuator: Upside-down, stem facing up.
*Locking Bar: Bottom down.
*Notch Cutting Template: Flattest facet, down.
Hardware Needed:
1x M8x30 Bolt, 1mm fine thread pitch (NOT 1.25mm)
1x M8 Washer, 15mm OD (Optional)
2x M4x30mm Bolts
2x M4x12mm (Or M4x15mm) Bolts
2x M4 Nuts
1x Compression Spring 3/8in x 3/4in
2x 6mm x 250mm Steel Rod
Adhesive Used: 2 Part Epoxy
(See ASSEMBLY.txt for fabrication and installation)
Accreditations:
Daikon & Doge: Used the same simple locking mechanism as the "Daikon x Dogenado MP5A3 Sliding Brace".
files
| File | Extension |
|---|---|
| ABS-1 (Yugo M70).zip | zip |
versions
Version: ABS-1 (Yugo M70 AK) V1.0.1 latest
ABS-1 (Yugo M70 AK): Laffs Dynamics
A hybrid design; the simplicity of a sliding wire buttstock, without the dogshit cheekweld that comes with them. Collapses down to 177mm/6.9in in length.
To extend the buttstock, simply pull back until the locking bar indexes with the corresponding notches in the 6mm rods. Vice versa, press the locking bar actuator in, and press forwards on the butt.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 32%+
Material Flow: 100%
Support Material Percentage: 16%
Print Orientations:
*Buttstock: Buttpad, down.
*Stock Mount: Widest, flattest facet, down.
*Locking Mech Mount: Front, non-angled facet down; Laffs logo upwards.
*Locking Actuator: Upside-down, stem facing up.
*Locking Bar: Bottom down.
*Notch Cutting Template: Flattest facet, down.
Hardware Needed:
1x M8x30 Bolt, 1mm fine thread pitch (NOT 1.25mm)
1x M8 Washer, 15mm OD (Optional)
2x M4x30mm Bolts
2x M4x12mm (Or M4x15mm) Bolts
2x M4 Nuts
1x Compression Spring 3/8in x 3/4in
2x 6mm x 250mm Steel Rod
Adhesive Used: 2 Part Epoxy
(See ASSEMBLY.txt for fabrication and installation)
Accreditations:
Daikon & Doge: Used the same simple locking mechanism as the "Daikon x Dogenado MP5A3 Sliding Brace".
Version: V1.0.1
M70 Picatinny Buttstock Adaptor V1.0.1: Laffs Dynamics
A 4 slot picatinny adaptor for Zastava (AKA Yugo) M70 AK variants.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 25%+
Material Flow: 100%
Support Material Percentage: 16%
Hardware Needed:
1x M8x30 Bolt, 1mm fine thread pitch (NOT 1.25mm)
1x M8 Washer, 15mm OD (Optional)
2x M4x12mm (Or M4x15mm) Bolts
2x M4 Nuts
Version: M70 Picatinny Buttstock Adaptor V1.0.1
M70 Picatinny Buttstock Adaptor V1.0.1: Laffs Dynamics
A 4 slot picatinny adaptor for Zastava (AKA Yugo) M70 AK variants.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 25%+
Material Flow: 100%
Support Material Percentage: 16%
Hardware Needed:
1x M8x30 Bolt, 1mm fine thread pitch (NOT 1.25mm)
1x M8 Washer, 15mm OD (Optional)
2x M4x12mm (Or M4x15mm) Bolts
2x M4 Nuts
Version: ABS-1 (Yugo M70 AK)
ABS-1 (Yugo M70 AK): Laffs Dynamics
A hybrid design; the simplicity of a sliding wire buttstock, without the dogshit cheekweld that comes
with them. Collapses down to 177mm/6.9in in length.
To extend the buttstock, simply pull back until the locking bar indexes with the corresponding notches
in the 6mm rods. Vice versa, press the locking bar actuator in, and press forwards on the butt.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 32%+
Material Flow: 100%
Support Material Percentage: 16%
Print Orientations:
*Buttstock: Buttpad, down.
*Stock Mount: Widest, flattest facet, down.
*Locking Mech Mount: Front, non-angled facet down; Laffs logo upwards.
*Locking Actuator: Upside-down, stem facing up.
*Locking Bar: Bottom down.
*Notch Cutting Template: Flattest facet, down.
Hardware Needed:
1x M8x30 Bolt, 1mm fine thread pitch (NOT 1.25mm)
1x M8 Washer, 15mm OD (Optional)
2x M4x30mm Bolts
2x M4x12mm (Or M4x15mm) Bolts
2x M4 Nuts
1x Compression Spring 3/8in x 3/4in
2x 6mm x 250mm Steel Rod
Adhesive Used: 2 Part Epoxy
(See ASSEMBLY.txt for fabrication and installation)
Accreditations:
Daikon & Doge: Used the same simple locking mechanism as the "Daikon x Dogenado MP5A3 Sliding Brace".
Version: 1.0.0
Initial release
about
ABS-1 (Yugo M70 AK): Laffs Dynamics
A hybrid design; the simplicity of a sliding wire buttstock, without the dogshit cheekweld that comes with them. Collapses down to 177mm/6.9in in length.
To extend the buttstock, simply pull back until the locking bar indexes with the corresponding notches in the 6mm rods. Vice versa, press the locking bar actuator in, and press forwards on the butt.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 32%+
Material Flow: 100%
Support Material Percentage: 16%
Print Orientations:
*Buttstock: Buttpad, down.
*Stock Mount: Widest, flattest facet, down.
*Locking Mech Mount: Front, non-angled facet down; Laffs logo upwards.
*Locking Actuator: Upside-down, stem facing up.
*Locking Bar: Bottom down.
*Notch Cutting Template: Flattest facet, down.
Hardware Needed:
1x M8x30 Bolt, 1mm fine thread pitch (NOT 1.25mm)
1x M8 Washer, 15mm OD (Optional)
2x M4x30mm Bolts
2x M4x12mm (Or M4x15mm) Bolts
2x M4 Nuts
1x Compression Spring 3/8in x 3/4in
2x 6mm x 250mm Steel Rod
Adhesive Used: 2 Part Epoxy
(See ASSEMBLY.txt for fabrication and installation)
Accreditations:
Daikon & Doge: Used the same simple locking mechanism as the "Daikon x Dogenado MP5A3 Sliding Brace".
creator
Metrics
Views
3.3K
Downloads
372
Project Info
release date
Nov 29, 2023
artifact type
library category
fabrication method
fabrication tool
3D Printer
release country
United States
language
English
license
Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International
files
| File | Extension |
|---|---|
| ABS-1 (Yugo M70).zip | zip |
versions
Version: ABS-1 (Yugo M70 AK) V1.0.1 latest
ABS-1 (Yugo M70 AK): Laffs Dynamics
A hybrid design; the simplicity of a sliding wire buttstock, without the dogshit cheekweld that comes with them. Collapses down to 177mm/6.9in in length.
To extend the buttstock, simply pull back until the locking bar indexes with the corresponding notches in the 6mm rods. Vice versa, press the locking bar actuator in, and press forwards on the butt.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 32%+
Material Flow: 100%
Support Material Percentage: 16%
Print Orientations:
*Buttstock: Buttpad, down.
*Stock Mount: Widest, flattest facet, down.
*Locking Mech Mount: Front, non-angled facet down; Laffs logo upwards.
*Locking Actuator: Upside-down, stem facing up.
*Locking Bar: Bottom down.
*Notch Cutting Template: Flattest facet, down.
Hardware Needed:
1x M8x30 Bolt, 1mm fine thread pitch (NOT 1.25mm)
1x M8 Washer, 15mm OD (Optional)
2x M4x30mm Bolts
2x M4x12mm (Or M4x15mm) Bolts
2x M4 Nuts
1x Compression Spring 3/8in x 3/4in
2x 6mm x 250mm Steel Rod
Adhesive Used: 2 Part Epoxy
(See ASSEMBLY.txt for fabrication and installation)
Accreditations:
Daikon & Doge: Used the same simple locking mechanism as the "Daikon x Dogenado MP5A3 Sliding Brace".
Version: V1.0.1
M70 Picatinny Buttstock Adaptor V1.0.1: Laffs Dynamics
A 4 slot picatinny adaptor for Zastava (AKA Yugo) M70 AK variants.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 25%+
Material Flow: 100%
Support Material Percentage: 16%
Hardware Needed:
1x M8x30 Bolt, 1mm fine thread pitch (NOT 1.25mm)
1x M8 Washer, 15mm OD (Optional)
2x M4x12mm (Or M4x15mm) Bolts
2x M4 Nuts
Version: M70 Picatinny Buttstock Adaptor V1.0.1
M70 Picatinny Buttstock Adaptor V1.0.1: Laffs Dynamics
A 4 slot picatinny adaptor for Zastava (AKA Yugo) M70 AK variants.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 25%+
Material Flow: 100%
Support Material Percentage: 16%
Hardware Needed:
1x M8x30 Bolt, 1mm fine thread pitch (NOT 1.25mm)
1x M8 Washer, 15mm OD (Optional)
2x M4x12mm (Or M4x15mm) Bolts
2x M4 Nuts
Version: ABS-1 (Yugo M70 AK)
ABS-1 (Yugo M70 AK): Laffs Dynamics
A hybrid design; the simplicity of a sliding wire buttstock, without the dogshit cheekweld that comes
with them. Collapses down to 177mm/6.9in in length.
To extend the buttstock, simply pull back until the locking bar indexes with the corresponding notches
in the 6mm rods. Vice versa, press the locking bar actuator in, and press forwards on the butt.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 32%+
Material Flow: 100%
Support Material Percentage: 16%
Print Orientations:
*Buttstock: Buttpad, down.
*Stock Mount: Widest, flattest facet, down.
*Locking Mech Mount: Front, non-angled facet down; Laffs logo upwards.
*Locking Actuator: Upside-down, stem facing up.
*Locking Bar: Bottom down.
*Notch Cutting Template: Flattest facet, down.
Hardware Needed:
1x M8x30 Bolt, 1mm fine thread pitch (NOT 1.25mm)
1x M8 Washer, 15mm OD (Optional)
2x M4x30mm Bolts
2x M4x12mm (Or M4x15mm) Bolts
2x M4 Nuts
1x Compression Spring 3/8in x 3/4in
2x 6mm x 250mm Steel Rod
Adhesive Used: 2 Part Epoxy
(See ASSEMBLY.txt for fabrication and installation)
Accreditations:
Daikon & Doge: Used the same simple locking mechanism as the "Daikon x Dogenado MP5A3 Sliding Brace".
Version: 1.0.0
Initial release
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.
