VFG-001
about
VFG 001: Laffs Dynamics
A medium length vertical foregrip with an oblong cross section.
Comes in three variants:
*Standard
*Ridged
*Perforated
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .2mm
Standard Layer Height: .14mm - .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 25%+
Infill Pattern: Gyroid
Support Material Percentage: 18%
Print the VFG upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm, so it doesn't stick out the side)
1x M4 Hex Nut
files
| File | Extension |
|---|---|
| VFG-001 V1.1.zip | zip |
versions
Version: VFG 001 V1.1 latest
VFG 001 V1.1: Laffs Dynamics
A medium length vertical foregrip with an oblong cross section.
Comes in three variants:
*Standard
*Ridged
*Perforated
Update V1.1: Tightened picatinny rail slot tolerances.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .2mm
Standard Layer Height: .14mm - .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 25%+
Infill Pattern: Gyroid
Support Material Percentage: 18%
Print the VFG upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm, so it doesn't stick out the side)
1x M4 Hex Nut
Version: 1.0.0
Initial release
about
VFG 001: Laffs Dynamics
A medium length vertical foregrip with an oblong cross section.
Comes in three variants:
*Standard
*Ridged
*Perforated
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .2mm
Standard Layer Height: .14mm - .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 25%+
Infill Pattern: Gyroid
Support Material Percentage: 18%
Print the VFG upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm, so it doesn't stick out the side)
1x M4 Hex Nut
creator
Metrics
Views
2.6K
Downloads
411
Project Info
release date
Jan 04, 2023
artifact type
library category
fabrication method
fabrication tool
3D Printer
release country
United States
language
English
license
files
| File | Extension |
|---|---|
| VFG-001 V1.1.zip | zip |
versions
Version: VFG 001 V1.1 latest
VFG 001 V1.1: Laffs Dynamics
A medium length vertical foregrip with an oblong cross section.
Comes in three variants:
*Standard
*Ridged
*Perforated
Update V1.1: Tightened picatinny rail slot tolerances.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .2mm
Standard Layer Height: .14mm - .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 25%+
Infill Pattern: Gyroid
Support Material Percentage: 18%
Print the VFG upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm, so it doesn't stick out the side)
1x M4 Hex Nut
Version: 1.0.0
Initial release
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.
