VFG 001-C: FFFTech/FFFTechnology
A compact version of the VFG 001.
Comes in three variants:
*Standard
*Ridged
*Perforated
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .2mm
Standard Layer Height: .14mm - .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 20%+
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%
Print the VFG upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm, so it doesn't stick out the side)
1x M4 Hex Nut
File | Extension |
---|---|
VFG 001-C V1.1.1.zip | zip |
Version: VFG 001-C V1.1.1 latest
VFG 001-C V1.1.1: Laffs Dynamics
A compact version of the VFG 001.
Comes in three variants:
*Standard
*Ridged
*Perforated
Update V1.1.1: Tightened picatinny rail slot tolerances. Relabeled designer's brand.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .2mm
Standard Layer Height: .14mm - .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 20%+
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%
Print the VFG upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm, so it doesn't stick out the side)
1x M4 Hex Nut
Version: 1.0.0
Initial release
VFG 001-C: FFFTech/FFFTechnology
A compact version of the VFG 001.
Comes in three variants:
*Standard
*Ridged
*Perforated
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .2mm
Standard Layer Height: .14mm - .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 20%+
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%
Print the VFG upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm, so it doesn't stick out the side)
1x M4 Hex Nut
2.9K
Oct 17, 2022
3D Printer
United States
English
File | Extension |
---|---|
VFG 001-C V1.1.1.zip | zip |
Version: VFG 001-C V1.1.1 latest
VFG 001-C V1.1.1: Laffs Dynamics
A compact version of the VFG 001.
Comes in three variants:
*Standard
*Ridged
*Perforated
Update V1.1.1: Tightened picatinny rail slot tolerances. Relabeled designer's brand.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .2mm
Standard Layer Height: .14mm - .16mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 20%+
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%
Print the VFG upside-down.
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm, so it doesn't stick out the side)
1x M4 Hex Nut
Version: 1.0.0
Initial release
The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.