Waco Waffle Hunter AK Magazine

about

Waco Waffle Hunter AK Magazine: Laffs Dynamics

A 10rd variant of the Waco Waffle Tanker.

Features a reinforced "waffle" style ribbed magazine body, HEAVILY inspired by Arsenal (Bulgarian) Circle 10 "Waffle" mags. Has a thickened baseplate to absorb impacts from drops, an anti-friction follower, and a separately printed rear locking lug.

This design also allows the use of AR-15 magazine springs via alternate follower and floorplate versions, for Western (North American countries) builders; as AR-15 magazine springs are often cheaper and easier to acquire. 


Tested with:

 * Palmetto State Armory PSAK-47 GF3, Domestic
 * Zastava ZPAP M70, Serbian Import


Two follower and floorplate versions are available: 

 *Standard: AK spring usage.
 *AR: AR-15 spring usage, labeled on each part. 

Shares most identical parts usage with the original 3FTech Revo1ution AK Magazine. (Baseplate is the exception.)

 

Printer Used: Ender 3 V2

Filament Used: PLA+

Print Settings:

Extruder: 220C
Bed: 56C 
First Layer Print Height: .2mm 
Standard Layer Height: .16mm
Wall Perimeters: 7+ 
Infill: 45%+
Infill Pattern: Gyroid
Support Material Percentage: 18%


Crispy Waffle Variant Print Settings (OPTIONAL):

Slicer Software: Cura

Fuzzy Skin: Enabled
Fuzzy Skin Outside Only: Enabled
Fuzzy Skin Thickness: .1mm
Fuzzy Skin Point Distance: .1mm

Print ALL the parts on their bases, and use tree supports for the front of the mag body and underneath the front lock lug. 

 

Hardware Needed:

1x 10rd Length AK Mag Spring

1x 10rd Length AR-15 Mag Spring (OPTIONAL)

(See NOTES below for options for acquiring mag springs)

 

Parts Installation:

1) Apply cyanoacrylate adhesive inside the pocket for the rear locking lug. If the rear locking lug is slightly loose in the pocket, apply Clear Gorilla Glue. Wait 24hrs for the adhesive to cure. 

2) Insert the rear locking lug, with the angled facet facing outwards, and down towards the mag body's base. 

3) Lightly sand the anti-friction follower's sides and curved spine. 

4) Slide the top of the magazine spring through the front of the follower, above the spring retention tab.

5) Attach the floorplate to the bottom of the magazine spring, making sure the first spring winding snaps over the retainers. 

6) Slide the internal spring assembly into the magazine body.

7) Depress the floorplate, and slide on the baseplate. The floorplate's locking tab must index with the channel in the baseplate. 

 

Notes: 

1) Bulgarian, Korean, and US based Magpul springs have been tested.

2) A 30rd AK mag springs cut in half will create two 20rd springs. (If that math doesn't make sense to you, often 40rd AK mags use 30rd mag springs.)

3) Cheapo Korean 10rd mags have been found to have longer springs than Magpul dedicated 20rd mags. Harvesting the springs from these mags are an alternative method for hardware acquirement if 30rd or 20rd mag springs are unable to be secured. 

 

files

File Extension
Waco Waffle Hunter AKM Magazine V1.1.1.zip zip

versions

Version: Waco Waffle Hunter AK Magazine V1.1.1 latest

Waco Waffle Hunter AK Magazine V1.1.1: Laffs Dynamics

 

A 10rd variant of the Waco Waffle Tanker.

 

Features a reinforced "waffle" style ribbed magazine body, HEAVILY inspired by Arsenal (Bulgarian) Circle 10 "Waffle" mags.

Has a thickened baseplate to absorb impacts from drops, an anti-friction follower, and a separately printed rear locking 

lug.

 

This design also allows the use of AR-15 magazine springs via alternate follower and floorplate versions, for Western 

(North American countries) builders; as AR-15 magazine springs are often cheaper and easier to acquire. 

 

 

Tested with:

 

 * Palmetto State Armory PSAK-47 GF3, Domestic

 * Zastava ZPAP M70, Serbian Import

 

 

Two follower and floorplate versions are available: 

 

 *Standard: AK spring usage.

 *AR: AR-15 spring usage, labeled on each part. 

 

Shares most identical parts usage with the original 3FTech Revo1ution AK Magazine. (Baseplate is the exception.)

 

 

Update V1.1.1: Raised rear locking lug by .4mm, shaved the rear of the feed lips by .5mm to allow for easier insertion

into tighter AK magwells. 

 

 

 

Printer Used: Ender 3 V2

 

Filament Used: PLA+

 

Print Settings:

 

Extruder: 220C

Bed: 56C 

First Layer Print Height: .2mm 

Standard Layer Height: .16mm

Wall Perimeters: 7+ 

Infill: 45%+

Infill Pattern: Gyroid

Support Material Percentage: 18%

 

 

Crispy Waffle Variant Print Settings (OPTIONAL):

 

Slicer Software: Cura

 

Fuzzy Skin: Enabled

Fuzzy Skin Outside Only: Enabled

Fuzzy Skin Thickness: .1mm

Fuzzy Skin Point Distance: .1mm

 

Print ALL the parts on their bases, and use tree supports for the front of the mag body and underneath the front 

lock lug. 

 

 

 

Hardware Needed:

 

1x 10rd Length AK Mag Spring

 

1x 10rd Length AR-15 Mag Spring (OPTIONAL)

 

(See NOTES below for options for acquiring mag springs)

 

 

 

Parts Installation:

 

1) Apply cyanoacrylate adhesive inside the pocket for the rear locking lug. If the rear locking lug is slightly loose 

in the pocket, apply Clear Gorilla Glue. Wait 24hrs for the adhesive to cure. 

 

2) Insert the rear locking lug, with the angled facet facing outwards, and down towards the mag body's base. 

 

3) Lightly sand the anti-friction follower's sides and curved spine. 

 

4) Slide the top of the magazine spring through the front of the follower, above the spring retention tab.

 

5) Attach the floorplate to the bottom of the magazine spring, making sure the first spring winding snaps over the 

retainers. 

 

6) Slide the internal spring assembly into the magazine body.

 

7) Depress the floorplate, and slide on the baseplate. The floorplate's locking tab must index with the channel in the 

baseplate. 

 

 

 

Notes: 

 

1) Bulgarian, Korean, and US based Magpul springs have been tested.

 

2) A 30rd AK mag springs cut in half will create two 20rd springs. (If that math doesn't make sense to you, often 40rd AK 

mags use 30rd mag springs.)

 

3) Cheapo Korean 10rd mags have been found to have longer springs than Magpul dedicated 20rd mags. Harvesting the springs 

from these mags are an alternative method for hardware acquirement if 30rd or 20rd mag springs are unable to be secured. 

 

4) Bulgarian Slabside Polymer AK mag followers, floorplates, and baseplates are compatible with the Waco Waffle series of 

magazines. 

 

 

 

Accreditations:

 

Cultivated Laser: Discovered ALL Bulgarian Slabside mag internals are compatible with the Waco Waffle Series of AKM mags.

Version: Waco Waffle Raider AK Magazine V1.0.1

Waco Waffle Raider AK Magazine V1.0.1: Laffs Dynamics

A 30rd variant of the original Waco Waffle Tanker.

Features a reinforced "waffle" style ribbed magazine body, HEAVILY inspired by Arsenal (Bulgarian) Circle 10 "Waffle" mags. Has a thickened baseplate to absorb impacts from drops, an anti-friction follower, and a separately printed rear locking lug.

This design ALSO allows the use of AR-15 magazine springs via alternate follower and floorplate versions, for Western (North American countries) builders; as AR-15 magazine springs are often cheaper and easier to acquire. 


Tested with:

 * Palmetto State Armory PSAK-47 GF3, Domestic
 * Zastava ZPAP M70, Serbian Import


Two follower and floorplate versions are available: 

 *Standard: AK spring usage.
 *AR: AR-15 spring usage, labeled on each part. 

Shares identical parts with the original Laffs Dynamics Waco Waffle Tanker AKM Mag; with the exception of using a 30rd magazine spring. 


Update V1.0.1: Added Bulgarian Slabside mag floorplates and baseplates to compatible parts list. Created folder of images Cultivated Laser sent of a laser etched magazine. Added contributor to credits for their work. 

 


Printer Used: Ender 3 V2

Filament Used: PLA+

Print Settings:

Extruder: 220C
Bed: 56C 
First Layer Print Height: .2mm 
Standard Layer Height: .16mm
Wall Perimeters: 7+ 
Infill: 45%+
Infill Pattern: Gyroid
Support Material Percentage: 18%

 

Hardware Needed:

1x 30rd Length AK Mag Spring

1x 30rd Length AR-15 Mag Spring (OPTIONAL)

 

Parts Installation:

1) Apply cyanoacrylate adhesive inside the pocket for the rear locking lug. If the rear locking lug is slightly loose in the pocket, apply Clear Gorilla Glue. Wait 24hrs for the adhesive to cure. 

2) Insert the rear locking lug, with the angled facet facing outwards, and down towards the mag body's base. 

3) Lightly sand the anti-friction follower's sides and curved spine. 

4) Slide the top of the magazine spring through the front of the follower, above the spring retention tab.

5) Attach the floorplate to the bottom of the magazine spring, making sure the first spring winding snaps over the retainers. 

6) Slide the internal spring assembly into the magazine body.

7) Depress the floorplate, and slide on the baseplate. The floorplate's locking tab must index with the channel in the baseplate. 

 

Notes: 

1) Bulgarian, Korean, and US based Magpul springs have been tested.

2) Bulgarian Slabside Polymer AK mag followers, floorplates, and baseplates are compatible with the Waco Waffle series of magazines. 

 

Accreditations:

Dianexis: Getting these mag designs out to sum based southern boyos. 

Cultivated Laser: Discovered ALL Bulgarian Slabside mag internals are compatible with the Waco Waffle Series of AKM mags.

Special Thanks To: Dianexis, GW-DD, ProSpaceDog, Freeman1337, and for the moral support of this project.

Version: 1.0.0

Initial release

about

Waco Waffle Hunter AK Magazine: Laffs Dynamics

A 10rd variant of the Waco Waffle Tanker.

Features a reinforced "waffle" style ribbed magazine body, HEAVILY inspired by Arsenal (Bulgarian) Circle 10 "Waffle" mags. Has a thickened baseplate to absorb impacts from drops, an anti-friction follower, and a separately printed rear locking lug.

This design also allows the use of AR-15 magazine springs via alternate follower and floorplate versions, for Western (North American countries) builders; as AR-15 magazine springs are often cheaper and easier to acquire. 


Tested with:

 * Palmetto State Armory PSAK-47 GF3, Domestic
 * Zastava ZPAP M70, Serbian Import


Two follower and floorplate versions are available: 

 *Standard: AK spring usage.
 *AR: AR-15 spring usage, labeled on each part. 

Shares most identical parts usage with the original 3FTech Revo1ution AK Magazine. (Baseplate is the exception.)

 

Printer Used: Ender 3 V2

Filament Used: PLA+

Print Settings:

Extruder: 220C
Bed: 56C 
First Layer Print Height: .2mm 
Standard Layer Height: .16mm
Wall Perimeters: 7+ 
Infill: 45%+
Infill Pattern: Gyroid
Support Material Percentage: 18%


Crispy Waffle Variant Print Settings (OPTIONAL):

Slicer Software: Cura

Fuzzy Skin: Enabled
Fuzzy Skin Outside Only: Enabled
Fuzzy Skin Thickness: .1mm
Fuzzy Skin Point Distance: .1mm

Print ALL the parts on their bases, and use tree supports for the front of the mag body and underneath the front lock lug. 

 

Hardware Needed:

1x 10rd Length AK Mag Spring

1x 10rd Length AR-15 Mag Spring (OPTIONAL)

(See NOTES below for options for acquiring mag springs)

 

Parts Installation:

1) Apply cyanoacrylate adhesive inside the pocket for the rear locking lug. If the rear locking lug is slightly loose in the pocket, apply Clear Gorilla Glue. Wait 24hrs for the adhesive to cure. 

2) Insert the rear locking lug, with the angled facet facing outwards, and down towards the mag body's base. 

3) Lightly sand the anti-friction follower's sides and curved spine. 

4) Slide the top of the magazine spring through the front of the follower, above the spring retention tab.

5) Attach the floorplate to the bottom of the magazine spring, making sure the first spring winding snaps over the retainers. 

6) Slide the internal spring assembly into the magazine body.

7) Depress the floorplate, and slide on the baseplate. The floorplate's locking tab must index with the channel in the baseplate. 

 

Notes: 

1) Bulgarian, Korean, and US based Magpul springs have been tested.

2) A 30rd AK mag springs cut in half will create two 20rd springs. (If that math doesn't make sense to you, often 40rd AK mags use 30rd mag springs.)

3) Cheapo Korean 10rd mags have been found to have longer springs than Magpul dedicated 20rd mags. Harvesting the springs from these mags are an alternative method for hardware acquirement if 30rd or 20rd mag springs are unable to be secured. 

 

download

creator

Metrics

Views

3.1K

Downloads

416

Project Info

release date

Mar 15, 2023

artifact type

Printable project

library category

Printable Magazines

fabrication method

Primarily Printable

fabrication tool

3D Printer

release country

United States

language

English

license

Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International

Firearm Info

type

Rifle

platform

AK-47

caliber

7.62x39

files

File Extension
Waco Waffle Hunter AKM Magazine V1.1.1.zip zip

versions

Version: Waco Waffle Hunter AK Magazine V1.1.1 latest

Waco Waffle Hunter AK Magazine V1.1.1: Laffs Dynamics

 

A 10rd variant of the Waco Waffle Tanker.

 

Features a reinforced "waffle" style ribbed magazine body, HEAVILY inspired by Arsenal (Bulgarian) Circle 10 "Waffle" mags.

Has a thickened baseplate to absorb impacts from drops, an anti-friction follower, and a separately printed rear locking 

lug.

 

This design also allows the use of AR-15 magazine springs via alternate follower and floorplate versions, for Western 

(North American countries) builders; as AR-15 magazine springs are often cheaper and easier to acquire. 

 

 

Tested with:

 

 * Palmetto State Armory PSAK-47 GF3, Domestic

 * Zastava ZPAP M70, Serbian Import

 

 

Two follower and floorplate versions are available: 

 

 *Standard: AK spring usage.

 *AR: AR-15 spring usage, labeled on each part. 

 

Shares most identical parts usage with the original 3FTech Revo1ution AK Magazine. (Baseplate is the exception.)

 

 

Update V1.1.1: Raised rear locking lug by .4mm, shaved the rear of the feed lips by .5mm to allow for easier insertion

into tighter AK magwells. 

 

 

 

Printer Used: Ender 3 V2

 

Filament Used: PLA+

 

Print Settings:

 

Extruder: 220C

Bed: 56C 

First Layer Print Height: .2mm 

Standard Layer Height: .16mm

Wall Perimeters: 7+ 

Infill: 45%+

Infill Pattern: Gyroid

Support Material Percentage: 18%

 

 

Crispy Waffle Variant Print Settings (OPTIONAL):

 

Slicer Software: Cura

 

Fuzzy Skin: Enabled

Fuzzy Skin Outside Only: Enabled

Fuzzy Skin Thickness: .1mm

Fuzzy Skin Point Distance: .1mm

 

Print ALL the parts on their bases, and use tree supports for the front of the mag body and underneath the front 

lock lug. 

 

 

 

Hardware Needed:

 

1x 10rd Length AK Mag Spring

 

1x 10rd Length AR-15 Mag Spring (OPTIONAL)

 

(See NOTES below for options for acquiring mag springs)

 

 

 

Parts Installation:

 

1) Apply cyanoacrylate adhesive inside the pocket for the rear locking lug. If the rear locking lug is slightly loose 

in the pocket, apply Clear Gorilla Glue. Wait 24hrs for the adhesive to cure. 

 

2) Insert the rear locking lug, with the angled facet facing outwards, and down towards the mag body's base. 

 

3) Lightly sand the anti-friction follower's sides and curved spine. 

 

4) Slide the top of the magazine spring through the front of the follower, above the spring retention tab.

 

5) Attach the floorplate to the bottom of the magazine spring, making sure the first spring winding snaps over the 

retainers. 

 

6) Slide the internal spring assembly into the magazine body.

 

7) Depress the floorplate, and slide on the baseplate. The floorplate's locking tab must index with the channel in the 

baseplate. 

 

 

 

Notes: 

 

1) Bulgarian, Korean, and US based Magpul springs have been tested.

 

2) A 30rd AK mag springs cut in half will create two 20rd springs. (If that math doesn't make sense to you, often 40rd AK 

mags use 30rd mag springs.)

 

3) Cheapo Korean 10rd mags have been found to have longer springs than Magpul dedicated 20rd mags. Harvesting the springs 

from these mags are an alternative method for hardware acquirement if 30rd or 20rd mag springs are unable to be secured. 

 

4) Bulgarian Slabside Polymer AK mag followers, floorplates, and baseplates are compatible with the Waco Waffle series of 

magazines. 

 

 

 

Accreditations:

 

Cultivated Laser: Discovered ALL Bulgarian Slabside mag internals are compatible with the Waco Waffle Series of AKM mags.

Version: Waco Waffle Raider AK Magazine V1.0.1

Waco Waffle Raider AK Magazine V1.0.1: Laffs Dynamics

A 30rd variant of the original Waco Waffle Tanker.

Features a reinforced "waffle" style ribbed magazine body, HEAVILY inspired by Arsenal (Bulgarian) Circle 10 "Waffle" mags. Has a thickened baseplate to absorb impacts from drops, an anti-friction follower, and a separately printed rear locking lug.

This design ALSO allows the use of AR-15 magazine springs via alternate follower and floorplate versions, for Western (North American countries) builders; as AR-15 magazine springs are often cheaper and easier to acquire. 


Tested with:

 * Palmetto State Armory PSAK-47 GF3, Domestic
 * Zastava ZPAP M70, Serbian Import


Two follower and floorplate versions are available: 

 *Standard: AK spring usage.
 *AR: AR-15 spring usage, labeled on each part. 

Shares identical parts with the original Laffs Dynamics Waco Waffle Tanker AKM Mag; with the exception of using a 30rd magazine spring. 


Update V1.0.1: Added Bulgarian Slabside mag floorplates and baseplates to compatible parts list. Created folder of images Cultivated Laser sent of a laser etched magazine. Added contributor to credits for their work. 

 


Printer Used: Ender 3 V2

Filament Used: PLA+

Print Settings:

Extruder: 220C
Bed: 56C 
First Layer Print Height: .2mm 
Standard Layer Height: .16mm
Wall Perimeters: 7+ 
Infill: 45%+
Infill Pattern: Gyroid
Support Material Percentage: 18%

 

Hardware Needed:

1x 30rd Length AK Mag Spring

1x 30rd Length AR-15 Mag Spring (OPTIONAL)

 

Parts Installation:

1) Apply cyanoacrylate adhesive inside the pocket for the rear locking lug. If the rear locking lug is slightly loose in the pocket, apply Clear Gorilla Glue. Wait 24hrs for the adhesive to cure. 

2) Insert the rear locking lug, with the angled facet facing outwards, and down towards the mag body's base. 

3) Lightly sand the anti-friction follower's sides and curved spine. 

4) Slide the top of the magazine spring through the front of the follower, above the spring retention tab.

5) Attach the floorplate to the bottom of the magazine spring, making sure the first spring winding snaps over the retainers. 

6) Slide the internal spring assembly into the magazine body.

7) Depress the floorplate, and slide on the baseplate. The floorplate's locking tab must index with the channel in the baseplate. 

 

Notes: 

1) Bulgarian, Korean, and US based Magpul springs have been tested.

2) Bulgarian Slabside Polymer AK mag followers, floorplates, and baseplates are compatible with the Waco Waffle series of magazines. 

 

Accreditations:

Dianexis: Getting these mag designs out to sum based southern boyos. 

Cultivated Laser: Discovered ALL Bulgarian Slabside mag internals are compatible with the Waco Waffle Series of AKM mags.

Special Thanks To: Dianexis, GW-DD, ProSpaceDog, Freeman1337, and for the moral support of this project.

Version: 1.0.0

Initial release

The files shown on this site are only available to U.S. Persons, as defined at 22 C.F.R. 120.15. The files are also not available to persons outside the United States or to residents of and persons in the State of New Jersey, with the exception of Federal Firearms Licensees.

Ghost Gunner 3s, GG3s, True Desktop CNC, by Defense Distributed Ghost Gunner 3s, GG3s, True Desktop CNC, by Defense Distributed

Javascript & cookies are required to view this site.